Clarke JET 8000 Operation & Maintenance Instructions Manual Download Page 4 | Manualshive

Page: 4 / 24

background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY SYMBOLS

WARNING:

Do not discharge the water

spray at persons or animals. Keep clear
of nozzle.

WARNING:

Never direct spray toward

any electrical device or electrical
outlet.

Read Instructions before use.

Wear Eye Protection

Wear Gloves

Equipment covered by the European
WEE (Waste Electrical/Electronic)
Directive.

«
...
2
3
4
5
6
...
»

Summary of Contents for JET 8000

























Reviews:

No comments

Related manuals for JET 8000

Brand: Makita Pages: 113

Brand: Campbell Hausfeld Pages: 8

Brand: Landa Pages: 24

Brand: Magic Chef Pages: 8

Brand: Candy Pages: 136

Brand: Candy Pages: 41

Brand: Kärcher Pages: 16

Brand: SMC Networks Pages: 20

Brand: Samsung Pages: 36

Brand: GE Pages: 72

Brand: Zanussi Electrolux Pages: 24

Brand: Dawlance Pages: 4

Brand: PAPILLON Pages: 55

AQUALTIS AQLF9F 49 U

Brand: Hotpoint Pages: 20

Brand: Bush Pages: 48

Lavadora y Secadora EWY8614W

Brand: EAS Electric Pages: 62

Brand: Candy Pages: 49

Brand: Frigidaire Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands