Clarke IMAGE 26E Operator'S Manual Download Page 3

Clarke

®

  Operator's  Manual  IMAGE  26E

             Page  -3-

OPERATOR SAFETY INSTRUCTIONS

WARNING

AVERTISSEMENT

ADVERTENCIA

DANGER:

Failure to read and observe all DANGER statements could result in
severe bodily injury or death.  Read and observe all DANGER
statements found in your Owner's Manual and on your machine.

WARNING:

Failure to read and observe all WARNING statements could result
in injury to you or to other personnel; property damage could
occur as well.  Read and observe all WARNING statements found in
your Owner's Manual and on your machine.

CAUTION:

Failure to read and observe all CAUTION statements could result in
damage to the machine or to other property.  Read and observe all
CAUTION statements found in your Owner's Manual and on your
machine.

DANGER:

Failure to read the Owner's Manual prior to operating or attempting any service or
maintenance procedure to your Clarke machine could result in injury to you or to
other personnel; damage to the machine or to other property could occur as well.
You must have training in the operation of this machine before using it.  If your
operator(s) cannot read English, have this manual explained fully before attempting
to operate this machine.

DANGER:

Operating a machine that is not completely or fully assembled could result in injury
or property damage.  Do not operate this machine until it is completely assembled.
Inspect the machine carefully before operation.

DANGER:

Machines can cause an explosion when operated near flammable materials and
vapors.  Do not use this machine with or near fuels, grain dust, solvents, thinners,
or other flammable materials.

DANGER:

Using a machine with a damaged power cord could result in an electrocution.  Do
not use the machine if the power cord is damaged.  Do not use the electrical cord
to move the machine.

DANGER

:

Electrocution could occur if maintenance and repairs are performed on a unit that is
not properly disconnected from the power source.  Disconnect the power supply
before attempting any maintenance or service.

DANGER

:

Electrocution could occur if the machine is used on a power circuit that repeatedly
trips or is undersized.  Have a licensed electrician check the fuse, circuit breaker
or power supply, and/or contact your local Clarke distributor for assistance.

WARNING:

Operating this machine from anywhere other than from the back of the machine could
result in injury or damage.  Operate this machine only from the rear.

WARNING:

This machine is heavy.  Get assistance before attempting to transport or move it. Use
two able persons to move the machine on a ramp or incline.  Always move slowly.  Do
not turn the machine on a ramp.  Do not stop and leave the machine on a ramp or incline.
Read the "Procedures For Transporting" in this manual before transporting.

WARNING:

Machines can topple over if guided over the edges of stairs or loading docks and cause
injury or damage.  Stop and leave this machine only on a level surface.  When you stop
the machine, put all switches into their "OFF" position.

https://harrissupplyind.com - To Order Parts Call 608-268-8080

Summary of Contents for IMAGE 26E







































Reviews: