English
Owner
’s manual
VRX848RVD/VRX743R
57
NAVI functions
When Clarion Navigation NAX943DV
(hereinafter referred to as NAVI) is connected,
the following functions are enabled:
• Showing the NAVI display;
• Operation is available by using the panel side
buttons.
• NAVI guidance sound interruption;
• Remote operation of navigation functions by
the remote controller through the optic sensor.
∗
If the operation of this unit is interrupted by a
NAVI operation, audio is switched to OFF.
∗
If the operation of this unit is interrupted by a
NAVI operation when the panel is closed, the sub-
LCD display is turned to “
NVG
”.
Setting Clarion NAVI as external
input equipment
Be sure to perform this setting after connecting
NAX943DV.
∗
The factory default setting is “
NONE
”.
1. When the panel is open, press the [
ADJ
] button
to show the adjustment selection display.
2. Touch the [
GENERAL
] key.
Touch the [
CONNECT
] key to display the
following items:
●
NAX DV
: When Clarion NAVI
(NAX943DV) is connected to the MINI DIN
8P connector and RGB terminal.
●
OTHR NVG
: When RGB image from a
Clarion navigation system (NAX9500E) is
connected to the RGB terminal.
●
COMPO
: When a composite image from
another manufacturer’s unit is connected
to the MINI DIN 8P connector.
●
OTHERS
: When an external device other
than a navigation system is connected to
the MINI DIN 8P connector.
3. Touch the [
NAX DV
] key to set connection of
NAX943DV.
Note:
• When the NAX943DV is connected with the unit,
be sure to set to [
NAX DV
]. Failure to set to
[
NAX DV
] results in malfunction.
NAVI operation
Changeover between NAVI display and Audio/
Visual (hereinafter referred to as AV) displays.
When the panel is open, the [
ADJ
] button has
the same function as the [
ADJ
] button on the
NAVI remote controller to set a screen mode
and a NAVI interruption.
Operate this button to change over between
NAVI and AV displays.
∗
When the NAVI Display/NAVI guidance sound
interruption setting (NAVI operation) is turned to
the NAVI/NAVI mode on this unit, the audio sound
is not heard.
1. Hold the [
ADJ
] button depressed for 1 second
or more to switch to navigation select screen.
•
If no command is made within 2 seconds, the
screen will switch back to the former screen.
2. When the [
ADJ
] button is pressed again, the
screen and audio statuses alternate as follows:
NVG
➜
NVG+BGM
➜
NVG-INT
➜
AV.
∗
These can be also selected directly by
touching the touch keys in the screen.
NVG:
Screen status NAVI, Audio status NAVI
NVG + BGM:
Screen status NAVI, Audio status audio
Note that in case of a NAVI interruption the
audio status is changed to NAVI.
NVG-INT:
Screen status Audio, Audio status audio
Note that in case of a NAVI interruption the screen
and audio statuses are both changed to NAVI.
AV:
Screen status audio, Audio status audio
When the NAVI display is shown with the panel
open. For the functions of the buttons for
navigation control, see “
4. NOMENCLATURE
”.
Note:
• These buttons become normal audio operating
buttons when changing into the AV display using
the [
ADJ
] button.
• If the receiver for remote control unit on the
NAX943DV is used, only the remote control unit for
NAVI comes effective and operation using the NAVI
operating buttons on the panel of the unit cannot be
performed. (For the NAVI operating buttons, refer to
the section “
4. NOMENCLATURE
”.)
• Set the NAVI side audio setting level to any
setting parameter value lower than 2.
●
Operations using the [DIRECT] buttons.
[
1
]
➜
[
DEST
] button : Setting a destination.
[
2
]
➜
[
MAP
] button : This displays the current
location map screen.
[
3
]
➜
[
SET
] button : Setting various settings.
[
4
]
➜
[
ROUTE
] button : Calculating or editing a
route.
[
5
]
➜
[
BACK
] button : This returns to the
previous screen.
[
6
]
➜
[
ZOOM
] button : The scale of the map can
be changed.
[
NVG/AV
] button : Use this button to
switch between the navigation screen and
audio/visual screen.
NAVI Operations (NAX943DV)
