Clarion UNGO ProSecurity SR5000 Owner'S Manual Download

Page: 45 / 52

prro

grra

miin

g o

pttiio

nss

Programming options control your system's normal, operational

set-up. Most options do not require additional parts, but some

may require installation labor.

The following is a list of the programmable options, with the

factory settings in Bold.

➤

Accttiivvee arming (transceiver only) or passive arming (auto-

matic arming 30 seconds after the last door has been closed).

➤

Arming/disarming siren chirps oon

n or off.

➤

The ignition controlled door lock feature oon

n or off: When

this feature is programmed on, the doors will lock three

seconds after the ignition is turned on, and unlock when the

ignition is turned off. If your installer is programming the

security system with the Pro Security Programmer, ignition

lock and unlock are independent features that can be

programmed separately.

➤

Passive door locking (with passive arming) or aaccttiivvee d

doooorr

lloocckkiin

ngg (only when arming with the transceiver). Passive

locking allows the vehicle's doors to lock when the security

system passively arms (after the 30-second countdown). This

feature only works if passive arming has been programmed.

➤

Panic mode een

naab

blleed

d/disabled when the ignition is turned

on. (Some states have laws against sirens sounding in moving

cars.)

Summary of Contents for UNGO ProSecurity SR5000





















































Search results

Summary of Contents for UNGO ProSecurity SR5000

Reviews:

Related manuals for UNGO ProSecurity SR5000

Brands by name

Popular brands

Clarion UNGO ProSecurity SR5000, Owner'S Manual

Search results

Summary of Contents for UNGO ProSecurity SR5000

Reviews:

Related manuals for UNGO ProSecurity SR5000

Brands by name

Popular brands