Clarion UNGO ProSecurity SR5000 Owner'S Manual Download

Page: 7 / 52

att iiss iin

cllu

➤

Control module

➤

A.S.K. Receiver

➤

One four-button two-way transceiver

➤

One four-button remote

➤

Two-stage shock sensor

➤

Six-tone programmable siren

➤

Red status LED indicator light

➤

Push-button override switch

➤

Your warranty registration

➤

Starter Kill

➤

Shut-down toggle switch

iim

orrtta

ntt iin

nffo

orrm

attiio

Congratulations on the purchase of your combination remote

engine start alarm system. Due to the complexity of this system,

it must only be installed by an authorized dealer. Installation of

this product by anyone other than an authorized dealer voids the

warranty.

By carefully reading this Owner's Guide prior to using your

system, you will maximize the use of this system and its features.

Summary of Contents for UNGO ProSecurity SR5000





















































Search results

Summary of Contents for UNGO ProSecurity SR5000

Reviews:

Related manuals for UNGO ProSecurity SR5000

Brands by name

Popular brands

Clarion UNGO ProSecurity SR5000, Owner'S Manual

Search results

Summary of Contents for UNGO ProSecurity SR5000

Reviews:

Related manuals for UNGO ProSecurity SR5000

Brands by name

Popular brands