Cisco RF Gateway 10 Release Notes Download Page 47

Page: 47 / 58

Release Notes for Cisco RF Gateway 10 in Cisco IOS Release 12.2SQ

OL-18677-10

Caveats

CSCta83794

Symptoms: The number of “FRURemoved” traps does not match the number of
“FRUInserted traps” from the RF Switch cards.

Conditions: This issue occurs when the TCC cards are switched over using the

redundancy tcc switchover

command. The RF Switch cards are part of the TCC

FRU. Therefore, when the TCC cards are switched over, the RF Switch cards to
generate the FRURemoved and FRUInserted traps.

Workaround: There is no workaround.

CSCtb86762

Symptoms: The

default

keyword does not set the default value for some QAM

CLIs.

Conditions: This issue was seen in the following commands:

cable downstream annex

cable downstream rf-shutdown

cable downstream stacking

Workaround: Set the default values manually for the commands.

cable downstream annex B

cable downstream rf-shutdown

cable downstream stacking 4

Caveat

Description

Summary of Contents for RF Gateway 10



























































Search results

Summary of Contents for RF Gateway 10

Reviews:

Related manuals for RF Gateway 10

Brands by name

Popular brands

Cisco RF Gateway 10, Release Notes

Search results

Summary of Contents for RF Gateway 10

Reviews:

Related manuals for RF Gateway 10

Brands by name

Popular brands