background image

14

Cisco 40-Gigabit QSFP+ Transceiver Modules Installation Note

OL-24862-01

  Attaching the Optical Network Cable

Note

The multiple-fiber push-on (MPO) connectors and the duplex LC connectors on the optical QSFP+ 
transceivers support network interface cables with either physical contact (PC) or ultra-physical contact 
(UPC) flat polished face types. The MPO and duplex LC connectors on the optical QSFP+ transceivers 
do not support network interface cables with an angle-polished contact (APC) face type.

Step 1

Remove the dust plugs from the optical network interface cable MPO connectors. Save the dust plugs 
for future use. 

Step 2

Inspect and clean the MPO or duplex LC connector’s fiber-optic end faces. See the Tip below for a 
pointer to a fiber-optic inspection and cleaning white paper.

Tip

For complete information on inspecting and cleaning fiber-optic connections, see this URL:

http://www.cisco.com/en/US/tech/tk482/tk876/technologies_white_paper09186a0080254eba.
shtml

Step 3

Remove the dust plugs from the QSFP+ transceiver module optical bores.

Step 4

Immediately attach the network interface cable MPO connector (see 

Figure 5

) or duplex LC connector 

(see 

Figure 6

) to the QSFP+ transceiver module.

Figure 5

Cabling a 40-Gigabit QSFP+ Transceiver Module Equipped with an MPO Connector

255434

Summary of Contents for QSFP+ Series

























Reviews: