Cisco NCS 5501 Hardware Installation Manual Download Page 77

Page: 77 / 82

A P P E N D I X

LEDs

•

Chassis LEDs, page 69

•

Fan Tray LED, page 71

•

Power Supply LEDs, page 72

Chassis LEDs

NCS 5501

: Attention (ATTN), STATUS, and ALARM LEDs are located on the bottom left front of the

chassis.

NCS 5501 SE and NCS 55A1-24H

: Attention (ATTN), STATUS, ALARM, and SYNC LEDs are located

along the left front of the chassis.

NCS 55A1-36H-S

: Attention (ATTN), Status (STAT), Alarm (ALRM), and SYNC LEDs are located along

the left front of the chassis.

NCS 5502

: Attention (ATTN), STATUS, and ALARM LEDs are located on the upper left front of the chassis.

Table 15: Fixed-Port Chassis LED Descriptions

Status

Color

LED

The operator has activated this LED to identify this chassis.

Flashing blue

ATTN

This chassis is not being identified.

Off

Hardware Installation Guide for Cisco NCS 5500 Series Fixed-Port Routers

Summary of Contents for NCS 5501



















































































Search results

Summary of Contents for NCS 5501

Reviews:

Related manuals for NCS 5501

Brands by name

Popular brands

Cisco NCS 5501, Hardware Installation Manual

Search results

Summary of Contents for NCS 5501

Reviews:

Related manuals for NCS 5501

Brands by name

Popular brands