Cisco NCS 5501 Hardware Installation Manual Download Page 72

Page: 72 / 82

Maximum Power

Typical Power

Weight per Unit

Component

Power Supply (2 maximum)

2.8 lb

•

NCS 55A1-36H-S

◦

Cisco NCS 5500 AC 2KW Power Supply Reverse
Airflow (Port side exhaust): NC55-2KW-ACRV(=)

◦

Cisco NCS 5500 AC 2KW Power Supply Forward
Airflow (Port side intake): NC55-2KW-ACFW(=)

◦

Cisco NCS 5500 DC 2KW Power Supply Reverse
Airflow (Port side exhaust): NC55-2KW-DCRV(=)

◦

Cisco NCS 5500 DC 2KW Power Supply Forward
Airflow (Port side intake): NC55-2KW-DCFW(=)

•

Cisco NCS 55A1-24 Chassis (NCS-55A1-24H)

◦

Cisco NCS 5500 1100W AC Power Supply, Forward
Airflow (Port side intake): NCS-1100W-ACFW

◦

Cisco NCS 5500 1100W AC Power Supply, Reverse
Airflow (Port side exhaust): NCS-1100W-ACRV

◦

Cisco NCS 5500 950Watts DC Power Supply,
Forward Airflow (Port side intake) NCS-950W-DCFW

◦

Cisco NCS 5500 1100W DC Power Supply, Reverse
Airflow (Port side exhaust): NCS-1100W-DCRV

Fan Tray (3 maximum)

See

Fan Tray Power

Consumption in
NCS 55A1

for

details.

See

Fan Tray Power

Consumption in
NCS 55A1

for

details.

10 Oz

•

NC55-A1-FAN-FW

•

NC55-A1-FAN-RV

Table 13: NCS-55A1-24H, NCS 55A1-36H-S Fan Tray Power Consumption

Total Fan Tray Power Consumption

Quantity of Fan trays

Power Consumption of Each Fan
Tray

Ambient Temperature

27W

25°C

108W

36W

55°C

Hardware Installation Guide for Cisco NCS 5500 Series Fixed-Port Routers

System Specifications

Weight, Quantity and Power Consumption

Summary of Contents for NCS 5501



















































































Search results

Summary of Contents for NCS 5501

Reviews:

Related manuals for NCS 5501

Brands by name

Popular brands

Cisco NCS 5501, Hardware Installation Manual

Search results

Summary of Contents for NCS 5501

Reviews:

Related manuals for NCS 5501

Brands by name

Popular brands