Cisco NCS 5501 Hardware Installation Manual Download Page 71

Page: 71 / 82

Maximum Power

Typical Power

Weight per Unit

Component

300W at 55°C

243W at 27°C

22.8 lbs (10.34 kgs)

Cisco NCS 5501 Chassis (NCS-5501)

330W at 55°C

280W at 25°C

23.5 lbs (10.66 kgs)

Cisco NCS 5501 SE Chassis (NCS-5501-SE)

Power Supply (2 maximum)

2.8 lb

•

NCS 5500 1100W AC Power Supply, Forward Airflow
(Port side intake): NCS-1100W-ACFW

•

NCS 5500 1100W AC Power Supply, Reverse Airflow (Port
side exhaust): NCS-1100W-ACRV

•

NCS 5500 950Watts DC Power Supply, Forward Airflow
(Port side intake) NCS-950W-DCFW

•

NCS 5500 1100W DC Power Supply, Reverse Airflow (Port
side exhaust): NCS-1100W-DCRV

See the following table for details

10 Oz

Fan Tray (2 maximum)

•

NCS-1RU-FAN-FW

•

NCS-1RU-FAN-RV

Table 11: NCS 5501 and NCS 5501 SE Fan Tray Power Consumption

Total Fan Tray Power Consumption

Quantity of Fan trays

Power Consumption of Each Fan
Tray

Ambient Temperature

22W

11W

25°C

82W

41W

55°C

NCS 55A1 Fixed Chassis Weight, Quantity and Power Consumption

The NCS 55A1 fixed chassis offers two hot-swappable power supplies providing

redundancy. For

redundancy mode, there must be two subsystems each, providing enough power supply to maintain the system.

Table 12: NCS 55A1-24H, NCS 55A1-36H-S Weight, Quantity and Power Consumption

Maximum Power

Typical Power

Weight per Unit

Component

Chassis

800W at 55°C

600W at 27°C

24 lbs (10.89 kgs)

Cisco NCS 55A1-24 Chassis (NCS-55A1-24H)

2000W at 55°C

1450W at 27°C

33 lbs (14.97 kgs)

Cisco NCS 55A1-36H-S Chassis (NCS-55A1-36H-S)

Hardware Installation Guide for Cisco NCS 5500 Series Fixed-Port Routers

System Specifications

Weight, Quantity and Power Consumption

Summary of Contents for NCS 5501



















































































Search results

Summary of Contents for NCS 5501

Reviews:

Related manuals for NCS 5501

Brands by name

Popular brands

Cisco NCS 5501, Hardware Installation Manual

Search results

Summary of Contents for NCS 5501

Reviews:

Related manuals for NCS 5501

Brands by name

Popular brands