Cisco NCS 5501 Hardware Installation Manual Download Page 37

Page: 37 / 82

A dual pole breaker is needed for the installation. The rating of the dual pole breaker for 110 V is 20 A
and for 220 V is 16 A. The minimum cable size is 14 AWG for 110 V and 16 AWG for 220 V.

Note

Step 1

Verify that the AC cable is installed in the correct AC source panel.

Step 2

Attach the AC power cable to the cable connector in the AC power module.

Figure 17: Connecting AC Power

Step 3

Place the cable through the opening in the cable clamp.

Step 4

Slide the cable clamp toward the plug.

Step 5

Close the cable clamp on the shoulder of the power cable to secure the power cable.

Wiring a DC Power Connector

Statement 1022

A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.

Warning

Hardware Installation Guide for Cisco NCS 5500 Series Fixed-Port Routers

Install the Chassis

Wiring a DC Power Connector

Summary of Contents for NCS 5501



















































































Search results

Summary of Contents for NCS 5501

Reviews:

Related manuals for NCS 5501

Brands by name

Popular brands

Cisco NCS 5501, Hardware Installation Manual

Search results

Summary of Contents for NCS 5501

Reviews:

Related manuals for NCS 5501

Brands by name

Popular brands