Cisco Linksys E2500, User Manual

Page: 35 / 38

Linksys E2500
Appendix A: Troubleshooting
32
Advanced Dual-Band N Router
Appendix A: Troubleshooting
Your computer cannot connect to the Internet.
Follow these instructions until your computer can connect
to the Internet:
•
Verify that the power adapter is connected to the
Router and to a power outlet . If connected to a power
strip, make sure the power strip is turned on .
•
Make sure that the Power LED, Internet LED, and
Wireless LED are on . If you have any wired computers
connected to the Router, make sure the appropriate
port LED is lit .
NOTE:
The Power LED flashes after the power
adapter is plugged in to the Router . If the light
remains flashing for more than 30 seconds,
it may indicate the Router is not working
properly . For assistance, use a computer or
device with Internet access to refer to our
Linksys E2500 support section on the web at
www.linksys.com/support
•
Make sure that your DSL or cable modem is connected
to your Router’s Internet port using an Ethernet cable .
•
Reset all of the devices on your network:
1 . Turn off all of your network computers and
devices, and then unplug the power adapter
from your Router .
2 . Unplug your modem’s power cord (and coaxial
cable if you have a cable modem), and wait two
minutes .
3 . Reconnect your modem’s power cord (and
coaxial cable) and wait two more minutes .
4 . Reconnect the power adapter to the Router, and
then power on all of your network computers
and devices .
The modem does not have an Ethernet port.
The modem is a dial-up modem for traditional dial-up
service . To use the Router, you need a cable/DSL modem
and high-speed Internet connection .
You cannot use the DSL service to connect manually to
the Internet.
After you have installed the Router, it will automatically
connect to your Internet Service Provider (ISP), so you no
longer need to connect manually .
The DSL telephone line does not fit into the Router’s
Internet port.
The Router does not replace your modem . You still need
your DSL modem in order to use the Router . Connect the
telephone line to the DSL modem, and then insert the
setup CD into your computer . Click
Set up your Linksys
Router and follow the on-screen instructions .
When you double-click the web browser, you are
prompted for a username and password. If you want to
get rid of the prompt, follow these instructions.
Launch the web browser and perform the following steps
(these steps are specific to Internet Explorer but are similar
for other browsers):
1 . Select Tools > Internet Options .
2 . Click the Connections tab .
3 . Select Never dial a connection .
4 . Click
OK
.
The Router does not have a coaxial port for the cable
connection.
The Router does not replace your modem . You still need
your cable modem in order to use the Router . Connect
your cable connection to the cable modem, and then
insert the setup CD into your computer . Click
Set up your
Linksys Router and follow the on-screen instructions .
The computer cannot connect wirelessly to the network.
Make sure the wireless network name or SSID is the same
on both the computer and the Router . If you have enabled
wireless security, then make sure the same security
method and key are used by both the computer and the
Router .
You need to modify the settings on the Router.
Router settings can be modified using the Cisco Connect
software, refer to “
How to Access Cisco Connect ” on
page 12 . To modify the advanced settings, go to Advanced
Settings . Refer to “ Advanced Settings ” on page 12 .
You want to access the browser-based utility from Cisco
Connect.
To enter the browser-based utility from Cisco Connect,
follow these steps:
1 . Open Cisco Connect .
2 . On the Main Menu, click
Router Settings .
3 . Click Advanced Settings .
4 . Write down the username and password that are
displayed . (To help protect your password, you can
copy it to the Clipboard by clicking
Copy Password .)
5 . Click
OK
.