Cisco ICS-7750 Description Download Page 72 | Manualshive

Page: 72 / 174

background image

Chapter 3 Summary of Power and Cooling System Features

Cisco ICS 7750 Chassis, Backplane, and Fan Tray

3-2

Cisco ICS 7750 System Description

78-10360-02

Figure 3-1

Cisco ICS 7750 Chassis

Note

The Federal Communications Commission (FCC) registration number of the
Cisco ICS 7750 is 5B1USA-40188-MF-E. The FCC number is also written on the
label affixed to the bottom of the chassis.

Key Features

The chassis, backplane, and fan tray have the following key features:

•

Two fixed, single-wide slots for the system alarm processor (SAP) card and
the system switch processor (SSP) card.

•

Six interchangeable slots for system processing engine (SPE), multiservice
route processor (MRP), and analog station interface (ASI) cards.

•

Two slots for the power supply modules.

•

Support for the standard 6U Eurocard form factor.

30344

INPUT

100-240V~

47-63Hz

3A

AC OK

OVERTEMP

DC OK

CISCO ICS 7700

SERIES

INTEGRATED COMMUNICATIONS SYSTEM

POWER SUPPLY 2

POWER SUPPLY 1

SLOT 8

SLOT 7

SLOT 6

SLOT 5

SLOT 4

SLOT 3

SLOT 2

SLOT 1

W

ARNING! RISK OF ELECTRIC SHOCK, REMO

VE BO

TH PO

WER CORDS BEFORE SER

VICING

SEE INSTR

UCTION MANU

AL BEFORE INST

ALLA

TION AND DISCONNECT

Power supply
module

Interchangeable

slots

Fixed

slots

Fan tray

Slot for redundant
power supply module

«
...
70
71
72
73
74
...
»

Summary of Contents for ICS-7750















































































































































































Reviews:

No comments

Related manuals for ICS-7750

Brand: VCON Pages: 48

Brand: Eclipse Pages: 5

Brand: Eclipse Pages: 21

COMPETITION ProZ4-80

Brand: µ-Dimension Pages: 7

Brand: IN-COMMAND Pages: 47

Brand: Dual Electronics Corporation Pages: 16

SE - 566 80 Habo

Brand: Fagerhult Pages: 6

SCOPIA XT MCU series

Brand: RADVision Pages: 43

Brand: Toa Pages: 12

Brand: Hama Pages: 76

MiVoice Business 3300 ICP

Brand: Mitel Pages: 366

Brand: RCA Pages: 19

Brand: Sharp Pages: 20

Brand: Samsung Pages: 16

Brand: Samsung Pages: 19

Brand: Samsung Pages: 19

Brand: Samsung Pages: 22

Brand: Samsung Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands