Cisco Catalyst 3650 Hardware Installation Manual Download Page 11

Page: 11 / 118

C H A P T E R

1-1

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Product Overview

The Catalyst 3650 series switches are Ethernet switches to which you can connect devices such as
Cisco IP Phones, Cisco Wireless Access Points, workstations, and other network devices such as servers,
routers, and other switches.

The Catalyst 3650 switches support stacking through Cisco StackWise-160 technology.

Unless otherwise noted, the term

switch

refers to a standalone switch and to a switch stack.

•

Switch Models, page 1-1

•

Front Panel, page 1-7

•

Rear Panel, page 1-22

•

Management Options, page 1-29

Switch Models

Table 1-1

Catalyst 3650 Switch Models

Switch Model

Cisco IOS Image

Description

WS-C3650-24TS-L

LAN Base

Stackable

24 10/100/1000 Ethernet downlink ports

4 1-Gigabit SFP (small form-factor pluggable)
uplink ports,

250-W power supply

WS-C3650-48TS-L

LAN Base

Stackable

48 10/100/1000 Ethernet downlink ports

4 1-Gigabit SFP uplink ports

250-W power supply

WS-C3650-24PS-L

LAN Base

Stackable

24 10/100/1000 PoE+

downlink ports

4 1-Gigabit SFP uplink ports

640-W power supply

Summary of Contents for Catalyst 3650























































































































Search results

Summary of Contents for Catalyst 3650

Reviews:

Related manuals for Catalyst 3650

Brands by name

Popular brands

Cisco Catalyst 3650, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 3650

Reviews:

Related manuals for Catalyst 3650

Brands by name

Popular brands