Cisco Catalyst 3650 Hardware Installation Manual Download Page 71

Page: 71 / 118

3-9

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Chapter 3 Power Supply Installation

Installing a DC Power Supply

Figure 3-9

Inserting the AC-Power Supply in the Switch

Step 6

(Optional) Make a loop in the power cord and thread it through the power cord retainer (

Figure 3-10

Figure 3-10

AC-Power Supply with Power Cord Retainer

Step 7

Connect the power cord to the power supply and to an AC power outlet. Turn on the power at the power
source.

Step 8

Confirm that the power supply

AC OK

and PS OK LEDs are green. See for a description of the power

supply module LEDs.

Installing a DC Power Supply

•

Equipment That You Need, page 3-10

•

Grounding the Switch, page 3-10

•

Installing the DC Power Supply in the Switch, page 3-13

•

Wiring the DC Input Power Source, page 3-13

Warning

An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure
that no exposed portion of the DC-input power source wire extends from the terminal block plug.

Statement 122

PWR-C2-640WAC

477

CONSOLE

MGMT

47769

AC OK

PWR-C

2-640W

PS OK

AC OK

PWR-C2-250W

PS OK

Summary of Contents for Catalyst 3650























































































































Search results

Summary of Contents for Catalyst 3650

Reviews:

Related manuals for Catalyst 3650

Brands by name

Popular brands

Cisco Catalyst 3650, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 3650

Reviews:

Related manuals for Catalyst 3650

Brands by name

Popular brands