Cisco Catalyst 3650 Hardware Installation Manual Download Page 84

Page: 84 / 118

4-2

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Chapter 4 Installing the Fan

Fan Module Installation

Figure 4-1

Fan Module

Fan Module Installation

Installation Guidelines

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Note

Fans should be removed or installed only when StackWise adapters or StackWise adapter blanks are
installed in each port.

Observe these guidelines when removing or installing a fan module:

•

Do not force the fan module into the slot. This can damage the pins on the switch if they are not
aligned with the module.

•

A fan module that is only partially connected can disrupt the system operation.

•

The switch supports hot swapping of the fan module. You can remove and replace the module
without interrupting normal switch operation.

Fan LED

Retainer clip

Exhaust vent

Extraction handles

344200

Summary of Contents for Catalyst 3650























































































































Search results

Summary of Contents for Catalyst 3650

Reviews:

Related manuals for Catalyst 3650

Brands by name

Popular brands

Cisco Catalyst 3650, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 3650

Reviews:

Related manuals for Catalyst 3650

Brands by name

Popular brands