35-7
Cisco Catalyst Blade Switch 3130 and 3032 for Dell Software Configuration Guide
OL-12247-04
Chapter 35 Configuring IPv6 ACLs
Configuring IPv6 ACLs
Step 3b
{
deny
|
permit
}
tcp
{
source-ipv6-prefix
/
prefix-length
|
any
|
host
source-ipv6-address
}
[
operator
[
port-number
]]
{
destination-ipv6-
prefix
/
prefix-length
|
any
|
host
destination-ipv6-address
}
[
operator
[
port-number
]]
[
ack
]
[
dscp
value
]
[
established
] [
fin
]
[
log
] [
log-input
] [
neq
{
port
|
protocol
}] [
psh
] [
range
{
port
|
protocol
}] [
rst
] [
routing
]
[
sequence
value
] [
syn
]
[
time-range
name
]
[
urg
]
(Optional) Define a TCP access list and the access conditions.
Enter
tcp
for Transmission Control Protocol. The parameters are the same as
those described in Step 3a, with these additional optional parameters:
•
ack
—
Acknowledgment bit set.
•
established
—
An established connection. A match occurs if the TCP
datagram has the ACK or RST bits set.
•
fin
—Finished bit set; no more data from sender.
•
neq
{
port
|
protocol
}
—
Matches only packets that are not on a given port
number.
•
psh
—Push function bit set.
•
range
{
port
|
protocol
}—Matches only packets in the port number range.
•
rst
—Reset bit set.
•
syn
—Synchronize bit set.
•
urg
—
Urgent pointer bit set.
Step 3c
{
deny
|
permit
}
udp
{
source-ipv6-prefix
/
prefix-length
|
any
|
host
source-ipv6-address
}
[
operator
[
port-number
]]
{
destination-ipv6-prefix
/
prefix-
length
|
any
|
host
destination-ipv6-address
}
[
operator
[
port-number
]]
[
dscp
value
]
[
log
] [
log-input
] [
neq
{
port
|
protocol
}] [
range
{
port
|
protocol
}] [
routing
] [
sequence
value
] [
time-range
name
]
(Optional) Define a UDP access list and the access conditions.
Enter
udp
for the User Datagram Protocol. The UDP parameters are the same
as those described for TCP, but the [
operator
[
port
]] port number or name must
be a UDP port number or name, and the
established
parameter is not valid for
UDP.
Step 3d
{
deny
|
permit
}
icmp
{
source-ipv6-prefix
/
prefix-length
|
any
|
host
source-ipv6-address
}
[
operator
[
port-number
]]
{
destination-ipv6-prefix
/
prefix-
length
|
any
|
host
destination-ipv6-address
}
[
operator
[
port-number
]]
[
icmp-type
[
icmp-code
] |
icmp-message
] [
dscp
value
]
[
log
]
[
log-input
] [
routing
] [
sequence
value
] [
time-range
name
]
(Optional) Define an ICMP access list and the access conditions.
Enter
icmp
for Internet Control Message Protocol. The ICMP parameters are
the same as those described for most IP protocols in Step 3a, with the addition
of the ICMP message type and code parameters. These optional keywords have
these meanings:
•
icmp-type
—Filter by ICMP message type. The range is from 0 to 255.
•
icmp-code
—Filter ICMP packets that are filtered by the ICMP message
code type. The range is from 0 to 255.
•
icmp-message
—Enter to filter ICMP packets by the ICMP message type
name or the ICMP message type and code name. To see a list of ICMP
message type names and code names, use the ? key or see command
reference for this release.
Step 4
end
Return to privileged EXEC mode.
Step 5
show ipv6 access-list
Verify the access list configuration.
Step 6
copy running-config
startup-config
(Optional) Save your entries in the configuration file.
Command
Purpose
