manualshive.com logo in svg

Cisco Catalyst 3130, Software Configuration Manual

The Cisco Catalyst 3130 is a high-performance networking switch designed for seamless data transfer. To ensure a smooth setup, make use of the comprehensive "Getting Started Manual" available for free download. Simply visit manualshive.com to access the manual and unlock the full potential of your Catalyst 3130 switch.

Share
Download
background image

C H A P T E R

 

13-1

Cisco Catalyst Blade Switch 3130 and 3032 for Dell Software Configuration Guide

OL-12247-04

13

Configuring VLANs

This chapter describes how to configure normal-range VLANs (VLAN IDs 1 to 1005) and 
extended-range VLANs (VLAN IDs 1006 to 4094) on the switch. It includes information about VLAN 
membership modes, VLAN configuration modes, VLAN trunks, and dynamic VLAN assignment from 
a VLAN Membership Policy Server (VMPS). Unless otherwise noted, the term 

switch

 refers to a 

standalone switch and to a switch stack.

Note

For complete syntax and usage information for the commands used in this chapter, see the command 
reference for this release.

The chapter consists of these sections:

•

Understanding VLANs, page 13-1

•

Configuring Normal-Range VLANs, page 13-4

•

Configuring Extended-Range VLANs, page 13-11

•

Displaying VLANs, page 13-14

•

Configuring VLAN Trunks, page 13-15

•

Configuring VMPS, page 13-27

Understanding VLANs

A VLAN is a switched network that is logically segmented by function, project team, or application, 
without regard to the physical locations of the users. VLANs have the same attributes as physical LANs, 
but you can group end stations even if they are not physically located on the same LAN segment. Any 
switch port can belong to a VLAN, and unicast, broadcast, and multicast packets are forwarded and 
flooded only to end stations in the VLAN. Each VLAN is considered a logical network, and packets 
destined for stations that do not belong to the VLAN must be forwarded through a router or a switch 
supporting fallback bridging, as shown in 

Figure 13-1

. In a switch stack, VLANs can be formed with 

ports across the stack. Because a VLAN is considered a separate logical network, it contains its own 
bridge Management Information Base (MIB) information and can support its own implementation of 
spanning tree. See 

Chapter 18, “Configuring STP.”

Note

Before you create VLANs, you must decide whether to use VLAN Trunking Protocol (VTP) to maintain 
global VLAN configuration for your network. For more information on VTP, see 

Chapter 14, 

“Configuring VTP.”

Summary of Contents for Catalyst 3130











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3130

PaloAlto Networks PA-500 Reference Manual preview
PA-500
Brand: PaloAlto Networks Pages: 20
PaloAlto Networks PA-3200 Series Quick Start Manual preview
PA-3200 Series
Brand: PaloAlto Networks Pages: 2
PaloAlto Networks PA-200 Hardware Reference Manual preview
PA-200
Brand: PaloAlto Networks Pages: 20
PaloAlto Networks PA-400 Series Hardware Reference Manual preview
PA-400 Series
Brand: PaloAlto Networks Pages: 60
PaloAlto Networks PA-7050 PAN-AIRDUCT Installation Manual preview
PA-7050 PAN-AIRDUCT
Brand: PaloAlto Networks Pages: 2
Draytek VigorPro 5510 Series User Manual preview
VigorPro 5510 Series
Brand: Draytek Pages: 316
Motorola SURFboard SVG2500 (Spanish) Guía Del Usuario preview
SURFboard SVG2500
Brand: Motorola Pages: 185
Fortinet FortiGate 3810A-LENC Quick Start Manual preview
FortiGate 3810A-LENC
Brand: Fortinet Pages: 2
US Robotics Modem/Router Brochure & Specs preview
Modem/Router
Brand: US Robotics Pages: 4
Trend Micro TippingPoint TPS 8200TX Installation Instructions Manual preview
TippingPoint TPS 8200TX
Brand: Trend Micro Pages: 9
Lindy 42758 Installation Manual preview
42758
Brand: Lindy Pages: 4

Brands by name

Popular brands

Load more brands