Cisco Catalyst 3130 Page 417 Software Configuration Manual Download | Manualshive

Page: 417 / 1354

background image

14-7

Cisco Catalyst Blade Switch 3130 and 3032 for Dell Software Configuration Guide

OL-12247-04

Chapter 14 Configuring VTP

Understanding VTP

shows a switched network with VTP pruning enabled. The broadcast traffic from Switch A

is not forwarded to Switches C, E, and F because traffic for the Red VLAN has been pruned on the links
shown (Port 5 on Switch B and Port 4 on Switch D).

Figure 14-2

Optimized Flooded Traffic with VTP Pruning

Enabling VTP pruning on a VTP server enables pruning for the entire management domain. Making
VLANs pruning-eligible or pruning-ineligible affects pruning eligibility for those VLANs on that trunk
only (not on all switches in the VTP domain).

See the

“Enabling VTP Pruning” section on page 14-16

. VTP pruning takes effect several seconds after

you enable it. VTP pruning does not prune traffic from VLANs that are pruning-ineligible. VLAN 1 and
VLANs 1002 to 1005 are always pruning-ineligible; traffic from these VLANs cannot be pruned.
Extended-range VLANs (VLAN IDs higher than 1005) are also pruning-ineligible.

VTP pruning is not designed to function in VTP transparent mode. If one or more switches in the
network are in VTP transparent mode, you should do one of these:

•

Turn off VTP pruning in the entire network.

•

Turn off VTP pruning by making all VLANs on the trunk of the switch upstream to the VTP
transparent switch pruning ineligible.

To configure VTP pruning on an interface, use the

switchport trunk pruning vlan

interface

configuration command (see the

“Changing the Pruning-Eligible List” section on page 13-22

). VTP

pruning operates when an interface is trunking. You can set VLAN pruning-eligibility, whether or not
VTP pruning is enabled for the VTP domain, whether or not any given VLAN exists, and whether or not
the interface is currently trunking.

Switch D

Switch E

Switch C

Switch F

Switch A

Switch B

Port 1

Port 2

Red

VLAN

89241

Port
4

Flooded traffic
is pruned.

Port
5

Flooded traffic
is pruned.

«
...
415
416
417
418
419
...
»

Summary of Contents for Catalyst 3130











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3130

H3C SecPath F1800-A

Brand: H3C Pages: 30

Brand: H3C Pages: 41

Brand: H3C Pages: 46

ZyWALL USG 100 Series

Brand: ZyXEL Communications Pages: 6

ZyXEL ZyWALL USG-1000

Brand: ZyXEL Communications Pages: 4

Brand: Fortinet Pages: 374

Dual WAN VPN Firewall VPN 2000

Brand: BaseWall Pages: 76

Brand: Cisco MERAKI Pages: 6

Brand: Cisco MERAKI Pages: 5

FortiGate FortiGate-5001FA2

Brand: Fortinet Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands