Cisco ASR1002 - ASR 1002 Router Installation Manual Download | Manualshive

Page: 39 / 46

background image

8-39

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation Guide

OL-13208-09

Chapter 8 Cisco ASR 1002 Router Overview and Installation

Cisco ASR 1002 Router Power Supplies

Figure 8-28

shows the +24 VDC power supply for the Cisco ASR 1002 Router.

Figure 8-28

+24 VDC Power Supply for the Cisco ASR 1002 Router Components

This section describes how to connect the +24 VDC power supply in the Cisco ASR 1002 Router.

Note

The color coding of the +24 VDC input power supply leads depends on the color coding of the +24 VDC
power source at your site. Typically, green or green/yellow is used for ground. Make certain the lead
color coding you choose for the +24 VDC input power supply matches lead color coding used at the +24
VDC power source. Most commonly used wire color-coding is red for positive (+) lead and black for
negative (–) lead.

Warning

When you install the unit, the ground connection must always be made first and disconnected last.

Statement 1046

To c24 VDC power supply in the Cisco ASR 1002 Router, follow these steps:

Step 1

At the rear of the router, check that the power Standby switch is in the Standby position.

Step 2

Ensure that the positive and negative leads are disconnected from the site power source and the source
circuit breaker is turned off.

Step 3

Using a wire stripper, strip the recommended amount of wire insulation which is 15mm (0.6 inch) from
the negative, positive, and ground leads.

Note

The stripping length is common to all types of wire used.

1

+24 VDC terminal block

6

Standby/On switch

2

Positive (+) lead

7

Captive fastener

3

Negative (-) lead

8

Power supply tabs

4

Ground (GND) lead

9

+27 VDC INPUT label

5

Power supply LEDs

—

—

OUTPUT INPUT

FAIL

OK

OK

FAN

+27V 32A

This unit might have more than
one power supply connection.
All connections must be removed
to de-energize the unit.

+27V DC INPUT

OUTPUT INPUT

FAIL

OK

OK

FAN

+27V 32A

This unit might have more than
one power supply connection.
All connections must be removed
to de-energize the unit.

+27V DC INPUT

2

3

1

5

6

0

1

7

4

7

8

253164

8

9

«
...
37
38
39
40
41
...
»

Summary of Contents for ASR1002 - ASR 1002 Router















































Reviews:

No comments

Related manuals for ASR1002 - ASR 1002 Router

Enterprise Filter Authentication R3000

Brand: 8e6 Technologies Pages: 66

Brand: Abus Pages: 60

Brand: Eaton Pages: 10

Brand: REXROTH Pages: 68

Brand: Telex Communications Pages: 28

Brand: Tripp Lite Pages: 3

TRAK 2OP M11 Mill

Brand: XYZ Machine Tools Pages: 203

Brand: TP-Link Pages: 7

Brand: TRENDnet Pages: 10

Brand: StarTech.com Pages: 9

Brand: Comelit Pages: 19

Sinus 154 data II

Brand: T-COM Pages: 12

Brand: Accton Technology Pages: 78

Slideaway CL1008

Brand: ATEN Pages: 77

24-Port 1000BASE-T

Brand: Comet Labs Pages: 44

Brand: Allied Telesis Pages: 2

Brand: Kentrox Pages: 246

Brand: HMS Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands