Cisco ASR1002 - ASR 1002 Router Installation Manual Download | Manualshive

Page: 19 / 46

background image

8-19

Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation Guide

OL-13208-09

Chapter 8 Cisco ASR 1002 Router Overview and Installation

Installing the Cisco ASR 1002 Router in a Rack

Step 1

Locate the threaded holes on the rear side of the chassis. Make certain that you hold the rear rack-mount
bracket with the ear and holes facing outward and towards the rear of the chassis.

Figure 8-13

shows where to attach the rear rack-mount brackets to the Cisco ASR 1002 Router.

Figure 8-13

Attaching the Rear Rack-Mount Brackets to the Cisco ASR 1002 Router

Step 2

Position the rear rack-mount bracket top hole with the chassis top hole from the back.

Step 3

Insert and tighten the screws on one side.

Step 4

Repeat Step 1 through Step 3 on the other side of the chassis. Use the remaining screws to secure the
rear rack-mount brackets to the chassis.

This completes the steps for attaching the rear rack-mount brackets to the Cisco ASR 1002 Router.

Caution

To make installation easier, before you mount the ASR 1002 Router in a rack, make certain you read
which rack-mount bracket ear holes to use when positioning the chassis in the rack. As a result of using
the designated ear holes on the rack-mount bracket, the cable-management bracket installation will be
made easier.

Installing the Cisco ASR 1002 Router in a Rack

After installing the rack-mount brackets on the chassis, you mount the chassis by securing the
rack-mount brackets to two posts or mounting strips in the rack using the screws provided. Because the
rack-mount brackets support the weight of the entire chassis, be sure to use all screws to fasten the two
rack-mount brackets to the rack posts.

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to ensure
your safety:
-This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

1

Rear rack-mount bracket ear and holes

3

Rear rack-mount bracket screws

2

Rear rack-mount bracket

—

—

280279

2

3

1

«
...
17
18
19
20
21
...
»

Summary of Contents for ASR1002 - ASR 1002 Router















































Reviews:

No comments

Related manuals for ASR1002 - ASR 1002 Router

Brand: D-Link Pages: 5

Brand: D-Link Pages: 2

Brand: TDC Pages: 27

OfficeConnect 1600

Brand: 3Com Pages: 8

Brand: 3Com Pages: 8

Brand: Campbell Pages: 42

Brand: H3C Pages: 22

Brand: H3C Pages: 3

Brand: Zonet Pages: 8

Brand: D-Link Pages: 176

Brand: ?omtime Pages: 62

Brand: Netopia Pages: 38

Brand: TRENDnet Pages: 2

Brand: Lanner Pages: 63

AyrMesh IndoorAP

Brand: AYRSTONE Pages: 2

System Storage DS3200

Brand: IBM Pages: 2

Brand: Abocom Pages: 63

Brand: XtendLan Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands