Cisco 7300-1OC12POS-MM Installation And Configuration Manual Download Page 33 | Manualshive

Page: 33 / 50

background image

3-3

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Chapter 3 Removing and Installing Line Cards

Line Card Removal and Installation

Caution

To prevent jamming the carrier between the upper and the lower edges of the slot, and to ensure that the
connector at the rear of the line card mates with the connection at the rear of the slot, make certain that
the carrier is positioned correctly, as shown in the cutaway in the following illustration. If the line card
does not slide freely into the backplane, loosen the locking thumbscrews on the neighboring line cards.

Warning

When performing the following procedures, wear a grounding wrist strap to avoid ESD damage to the
card. Some platforms have an ESD connector for attaching the wrist strap. Do not directly touch the
midplane or backplane with your hand or any metal tool, or you could shock yourself.

Line Card Removal and Installation

In this section, the illustration that follows gives step-by-step instructions on how to remove and install
line cards in the following supported platform:

•

Cisco 7304—Removing and Installing a Line Card, page 3-4

«
...
31
32
33
34
35
...
»

Summary of Contents for 7300-1OC12POS-MM



















































Reviews:

No comments

Related manuals for 7300-1OC12POS-MM

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 11

Brand: Nauticam Pages: 2

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 20

GEMINI C Series

Brand: NAPCO Pages: 24

Brand: Parker Pages: 32

Brand: Rayrun Pages: 4

AeGIS 7000 Series

Brand: PACH & COMPANY Pages: 2

Brand: T&S Pages: 5

FT-2000 - MENU MODE LIST

Brand: Yaesu Pages: 56

Brand: Nordelettronica Pages: 8

653 - AE Series

Brand: VAT Pages: 103

eTracer ET4415BND

Brand: Epsolar Pages: 44

Brand: Graco Pages: 166

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands