Cisco 7300-1OC12POS-MM Installation And Configuration Manual Download Page 15 | Manualshive

Page: 15 / 50

background image

1-3

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Chapter 1 Overview

SONET/SDH Overview

Figure 1-5

7300-2OC12POS-SMI—Faceplate View

Figure 1-6

7300-2OC12POS-SML—Faceplate View

SONET/SDH Overview

The POS specification addresses the use of PPP encapsulation over SONET/Synchronous Digital
Hierarchy (SDH) links. SONET is an American National Standards Institute (ANSI) standard
(T1.1051988) for optical digital transmission at hierarchical rates from 51.840 Mbps (STS-1) to 622.080
Mbps (STS-12) and greater. SDH is the international standard for optical digital transmission at
hierarchical rates from 155.520 Mbps (STM-1) to 2.488 Gbps (STM-16) and greater.

SONET is an octet-synchronous multiplex scheme that defines a family of standard rates and formats.
The basic rate for POS is that of STS-3c/STM-1, which is 155.520 Mbps. The available information
bandwidth is 149.760 Mbps, which is the STS-3c/STM-1 Synchronous Payload Envelope (SPE), the
payload portion of the SONET frame into which the octet-oriented user data is mapped. (Octet
boundaries are aligned with the SPE octet boundaries.)

The International Telecommunication Union Telecommunication Standardization Sector (ITU-T)
defines a series of SDH transmission rates beginning at 155.520 Mbps as follows:

7300-2OC12POS-SMI

2-PORT OC-12 POS SM IR

OIR

STATUS

CARRIER/

ALARM

ACTIVE/
LOOPBACK

75155

RX

0

TX

CARRIER/

ALARM

ACTIVE/
LOOPBACK

RX

1

TX

7300-2OC12POS-SML

2-PORT OC-12 POS SM LR

OIR

STATUS

CARRIER/

ALARM

ACTIVE/
LOOPBACK

75154

RX

0

TX

CARRIER/

ALARM

ACTIVE/
LOOPBACK

RX

1

TX

SONET

1

1.

ANSI-defined SONET specifications.

SDH Equivalent

STS-3c

STM-1

STS-12c

2

2.

Currently supported by the OC12 POS line card.

STM-4c

STS-48c

STM-16c

«
...
13
14
15
16
17
...
»

Summary of Contents for 7300-1OC12POS-MM



















































Reviews:

No comments

Related manuals for 7300-1OC12POS-MM

Brand: unicore Pages: 25

Brand: unicore Pages: 24

Brand: Lawler Pages: 2

Brand: MADRIX Pages: 36

AirGENIO SUPERIOR

Brand: 2VV Pages: 27

vlt soft starter mcd 500

Brand: Danfoss Pages: 95

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 33

Brand: Danfoss Pages: 59

Brand: Danfoss Pages: 16

VLT AQUA Drive FC 200

Brand: Danfoss Pages: 91

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 100

Brand: Danfoss Pages: 82

Brand: Danfoss Pages: 18

Brand: Danfoss Pages: 12

OPTYMA Plus OP-LPQM

Brand: Danfoss Pages: 8

Brand: QUAD Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands