Cisco 7300-1OC12POS-MM Installation And Configuration Manual Download Page 19

Page: 19 / 50

1-7

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Chapter 1 Overview

LEDs

Alarms

A yellow CARRIER/ALARM LED indicates the presence of an alarm condition.

Table 1-3

lists the

alarm conditions that might be present. Use the show controllers command to show the specific alarm
condition.

CARRIER/ALARM

Green/Yellow

Green

Indicates that a valid SONET signal has been
detected with no alarm conditions.

Yellow

Indicates that an alarm condition is present. See

Table 1-3

for alarm definitions.

Off

No valid SONET signal has been detected.

ACTIVE/

LOOPBACK

Green/Yellow

Green

Indicates that the port has been configured and is
enabled.

Yellow

Indicates that the port is in diagnostic loopback
mode.

Off

Indicates that the port has not been configured.

Table 1-2

OC12 POS Line Card LEDs (continued)

LED Label

Color

State

Function

Table 1-3

Alarm Definitions

Alarm

Definition

Section

LOF

loss of frame

LOS

loss of signal

BIP(B1)

Bit Interleaved Parity N

Line

AIS

alarm indication signal

RDI

remote defect indication

FEBE

far end block error

BIP(B2)

Bit Interleaved Parity N

Path

AIS

alarm indication signal

RDI

remote defect indication

FEBE

far end block error

BIP(B3)

Bit Interleaved Parity N

PLM

Path Payload Label Mismatch

UNEQ

Path Unequipped

TIM

Trace Identifier Mismatch

TIU

Trace Identifier Unstable

LOP

loss of pointer

Summary of Contents for 7300-1OC12POS-MM



















































Search results

Summary of Contents for 7300-1OC12POS-MM

Reviews:

Related manuals for 7300-1OC12POS-MM

Brands by name

Popular brands

Cisco 7300-1OC12POS-MM, Installation And Configuration Manual

Search results

Summary of Contents for 7300-1OC12POS-MM

Reviews:

Related manuals for 7300-1OC12POS-MM

Brands by name

Popular brands