Cisco 7300-1OC12POS-MM Installation And Configuration Manual Download Page 9 | Manualshive

Page: 9 / 50

background image

9

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Preface

Obtaining Technical Assistance

Documentation CD-ROM

Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM
package, which is shipped with your product. The Documentation CD-ROM is updated monthly and may
be more current than printed documentation. The CD-ROM package is available as a single unit

or

through an annual subscription.

Ordering Documentation

Cisco documentation is available in the following ways:

•

Registered Cisco Direct Customers can order Cisco product documentation from the Networking
Products MarketPlace:

http://www.cisco.com/cgi-bin/order/order_root.pl

•

Registered Cisco.com users can order the Documentation CD-ROM through the online Subscription
Store:

http://www.cisco.com/go/subscription

•

Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco corporate headquarters (California, USA) at 408 526-7208 or, elsewhere in North
America, by calling 800 553-NETS (6387).

Documentation Feedback

If you are reading Cisco product documentation on Cisco.com, you can submit technical comments
electronically. Click Leave Feedback at the bottom of the Cisco Documentation home page. After you
complete the form, print it out and fax it to Cisco at 408 527-0730.

You can e-mail your comments to [email protected].

To submit your comments by mail, use the response card behind the front cover of your document, or
write to the following address:

Cisco Systems

Attn: Document Resource Connection

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can
obtain documentation, troubleshooting tips, and sample configurations from online tools by using

the

Cisco Technical Assistance Center (TAC) Web Site. Cisco.com registered users have complete access
to the technical support resources on the Cisco TAC Web Site.

«
...
7
8
9
10
11
...
»

Summary of Contents for 7300-1OC12POS-MM



















































Reviews:

No comments

Related manuals for 7300-1OC12POS-MM

Brand: Nelson Pages: 19

Brand: C-TEC Pages: 2

Brand: Value Point Pages: 7

IntelliZone2 MasterStat

Brand: Water Furnace Pages: 44

Brand: Zaiput Flow Technologies Pages: 10

Pearldex Series

Brand: KaMo Pages: 2

Brand: Comparato Pages: 20

Brand: Inkel Pages: 12

Brand: Waeco Pages: 168

Brand: J+J Pages: 56

Brand: Generac Power Systems Pages: 20

Brand: C&C Pages: 17

Brand: Lab-T Pages: 7

Powador XP Series

Brand: Kaco Pages: 10

Brand: Control Techniques Pages: 38

Brand: PPI Pages: 27

Brand: NuTone Pages: 4

Brand: AXIOMTEK Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands