manualshive.com logo in svg

Cisco 3110, Message Manual

Share
Download
Cisco 3110 Message Manual Download Page 83

 

2-67

Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide

OL-12191-01

Chapter 2      Message and Recovery Procedures

PM Messages

Error Message   

PM-4-ERR_RECOVER: Attempting to recover from [chars] err-disable state 

on [chars]. 

Explanation   

The port manager is attempting to bring the interface up after taking it down to the 

error-disabled state. The first [chars] is the error, and the second [chars] is the affected interface.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Enter the 

show 

tech-support 

user EXEC command to gather data that might help identify the nature of the error. 

Use the Bug Toolkit to look for similar reported problems. If you still require assistance, contact 
IBM technical support and provide the representative with the gathered information. For more 
information about the online tools and about contacting IBM, see the 

“Error Message Traceback 

Reports” section on page 1-6

.

Error Message   

PM-4-ERR_RECOVER_VP: Attempting to recover from [chars] err-disable 

state on [chars], vlan [dec]. 

Explanation   

The port manager is attempting to bring up the virtual port after taking it down to the 

error-disabled state. The first [chars] is the error, the second [chars] is the virtual port, and [dec] is 
the VLAN ID.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error using the Output Interpreter. Use the Bug Toolkit to look 
for similar reported problems. If you still require assistance, open a case with the TA C, or contact 
your Cisco technical support representative, and provide the representative with the gathered 
information. For more information about these online tools and about contacting Cisco, see the 

“Error 

Message Traceback Reports” section on page 1-6

.

Error Message   

PM-4-EXT_VLAN_INUSE: VLAN [dec] currently in use by [chars]. 

Explanation   

The port manager failed to allocate the VLAN for external use because the VLAN is 

being used by another feature. [dec] is the VLAN that is being used, and [chars] is the feature that 
is using it.

Recommended Action   

Reconfigure the feature (for example, the routed port) to use another internal 

VLAN or to request another available VLAN.

Error Message   

PM-4-EXT_VLAN_NOTAVAIL: VLAN [dec] not available in Port Manager. 

Explanation   

The port manager failed to allocate the requested VLAN. The VLAN is probably being 

used as an internal VLAN by other features. [dec] is the requested VLAN.

Recommended Action   

Try to configure a different VLAN on the device.

Summary of Contents for 3110







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands