Cisco 2801 - Integrated Services Router User Manual Download Page 17 | Manualshive

Page: 17 / 204

background image

Corporate Headquarters:

© 2006 Cisco Systems, Inc. All rights reserved.

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Installing and Upgrading Fans in Cisco 2811
Series Routers

This document describes how to install or upgrade fans that are located internally within a Cisco 2811
series integrated services router. You need to remove the cover from the router to install or remove any
of these items. The document contains the following sections:

•

Safety Warnings, page 1

•

Removing the Chassis Cover, page 2

•

Locating the Fan, page 5

•

Installing and Removing the Fans, page 5

•

Installing the Chassis Cover, page 13

Before you begin the fan replacement procedure, disconnect the power and remove the cover, as
described in the

“Removing the Chassis Cover” section on page 2

. After you complete the fan

replacement procedure, install the chassis cover as described in the

“Installing the Chassis Cover”

section on page 13

.

Safety Warnings

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.

Statement 1024

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.

Statement 1

«
...
15
16
17
18
19
...
»

Summary of Contents for 2801 - Integrated Services Router













































































































































































































Reviews:

No comments

Related manuals for 2801 - Integrated Services Router

Brand: D-Link Pages: 2

Brand: Cambium Networks Pages: 29

Brand: dixell Pages: 4

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: Tektronix Pages: 178

Brand: Galaxy Pages: 30

Brand: BEC Pages: 159

Brand: KYLAND Technology Pages: 24

Brand: ADDON Pages: 4

Brand: Quantum Pages: 108

Fibe-Air IP-10G

Brand: Ceragon Pages: 71

Brand: Enterasys Pages: 2

Brand: Omron Pages: 4

Brand: Linksys Pages: 37

Brand: Opengear Pages: 4

Temporary Target Board M38517T-ADS

Brand: Renesas Pages: 14

Firebox T85-PoE

Brand: Watchguard Pages: 27

Brand: Billion Pages: 183

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands