Cisco 2801 - Integrated Services Router User Manual Download Page 72 | Manualshive

Page: 72 / 204

background image

6

Port and Cable Information for Cisco 2800 Series Routers

OL-5785-01

Preparing to Connect to a Network

For more information on BRI WAN interface cards, refer to the

Cisco Interface Cards Installation Guide

online document on Cisco.com.

CSU/DSU Connections

CSU/DSU WAN interface cards (WICs) are available to provide switched-56-kbps connections or full
or fractionalized T1 connections.

For more information on CSU/DSU WICs, refer to the

Cisco Interface Cards Installation Guide

online

document on Cisco.com.

Copyright © 2004 Cisco Systems, Inc. All rights reserved.

Table 3

ISDN BRI Cable Specifications

Specification

High-Capacitance Cable

Low-Capacitance Cable

Resistance (at 96 kHz)

160 ohms/km

160 ohms/km

Capacitance (at 1 kHz)

120 nF

1

/km

1.

nF = nanoFarad

30 nF/km

Impedance (at 96 kHz)

75 ohms

150 ohms

Wire diameter

0.024 in. (0.6 mm)

0.024 in. (0.6 mm)

Distance limitation

32.8 ft (10 m)

32.8 ft (10 m)

CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is
a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco
Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity,
Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS,
iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers,
Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient,
and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (0711R)

«
...
70
71
72
73
74
...
»

Summary of Contents for 2801 - Integrated Services Router













































































































































































































Reviews:

No comments

Related manuals for 2801 - Integrated Services Router

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 30

Brand: Wattle Pages: 6

Brand: Baicells Pages: 8

Ray 3 Plus Client

Brand: Sun Microsystems Pages: 6

Brand: N-Tron Pages: 62

Brand: Paradyne Pages: 112

Brand: Cambium Networks Pages: 215

Brand: Winext Pages: 37

Fast SwitchHub-8mi SNMP

Brand: Accton Technology Pages: 13

Brand: Allnet Pages: 12

Brand: Telebyte Pages: 19

Brand: RAIDAGE Pages: 60

Brand: Schrack Technik Pages: 2

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

Brand: SriHome Pages: 12

airMAX NanoBridge M NBM3

Brand: Ubiquiti Pages: 24

Blue Gate ISDN BRI Brave

Brand: Alphatech Pages: 6

Mobileraid MR8X

Brand: Sans Digital Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands