manualshive.com logo in svg

Cisco 10008, Installation And Configuration Manual, Page: 7 / 70

Share
Download
Cisco 10008 Installation And Configuration Manual Download Page 7

7

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

  Prerequisites and Preparation

Prerequisites and Preparation

Before you perform any of the procedures in this guide, we recommend that you:

•

Read the safety guidelines in the next section and review the electrical safety and ESD-prevention 
guidelines as described in the 

Cisco 10008 Router Hardware Installation Guide

 

at the following url: 

http://cisco.com/en/US/docs/routers/10000/10008/install_and_upgrade/hardware_installation/
guide/8-hig.html

•

Ensure that the software configuration meets the minimum requirements for the installation (see the 

“Software Compatibility” section on page 8

).

•

Ensure that you have all of the necessary tools and equipment before beginning the installation (see 
the 

“Installation Guidelines” section on page 8

).

•

Have a terminal console connected to the PRE4 to configure the PRE4 after it is installed.

The following publications can be used as reference material while performing procedures in this 
document:

–

Cisco 10000 Series Router Performance Routing Engine Installation

 at: 

http://cisco.com/en/US/products/hw/routers/ps133/
prod_installation_guide09186a0080525aba.html

–

Cisco 10000 Series Internet Router Troubleshooting Guide

 at:

http://cisco.com/en/US/products/hw/routers/ps133/
prod_troubleshooting_guide_book09186a00807a1043.html

Safety Guidelines

Before you begin the PRE4 installation procedure, review the safety guidelines in this section to avoid 
injuring yourself or damaging the equipment. Before you install, configure, or perform maintenance on 
the router, you should also review the safety warnings listed in the 

Regulatory Compliance and Safety 

Information for the Cisco 10000 Series Routers

 document.

IOS STRT, IOS EXC, IOS FPGA, IOS 
FPOK, IOS FILE, IOS STBY, IOS INTF, 
IOS MEM, IOS DRVR, IOS LIB, IOS 
MGMT, IOS PROT, IOS CONF 

These messages appear in quick succession during the 
boot process. 

IOS RUN

[On the primary PRE4] The PRE4 has finished booting 
and is running Cisco IOS. This is the normal operating 
status for the primary PRE. 

IOS STBY 

[On the secondary PRE4] The PRE4 is in standby mode 
and ready to take over if the primary PRE4 fails. This is 
the normal operating status for the secondary PRE4. 

Table 3

Messages on PRE4 Alphanumeric Display 

Message

PRE4 Status

Summary of Contents for 10008







































































Reviews:

No comments