Cisco 10008 Installation And Configuration Manual Download Page 44

Page: 44 / 70

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

Analyzing and Troubleshooting Packets

atm_vc=Not an ATM VC, mqc_gqid=0x0, lblt flags=0x4

HW Logical BLT: qid=72

pblt=19 quantum=10000 (Y=29, X=53688) w=1 (brr=166)

Shape: x=0 y=0 (0 bps) invx=0 invy=0 maxTokens=0

pkt_size_adj_type=PKT_SIZE_ADJ_TYPE_PRE3_NORMAL user_defined_overhead=0

curr_token=0xFFFFFFC0 last_timestamp=0x00000000

Flow Control: period=0 offset=0 frag=4095 byte=0 res=0

ML / LFI: ml_lfi_flag=0 ml_size=0 start_flag=0 delay_start=1

Physical BLT Shadow data: qid=19

hwidb=GigabitEthernet1/3/1, pbt flags=0x0

Bandwidths max=1000000 kbps, current=1000000 kbps, shaped=0kbps

2 child lblts: 70 72

HW Physical BLT: qid=19

bwm=39322, bws=14,(999989827 bps), resource=11, burst_limit=6826, channel=113

flow_period=8, flow_offset=1, flow_resource=14

col6_burst_limit=169, pkt_size_adj_type=1, flowoff_byte=0

vtp_bwm=0, vtp_bws=0, vtp_burst=0, next_send_blt=19, pblt=19

Displaying Drop Statistics

The

show pxf cpu statistics drop

command provides information about dropped packets and ICMP

packets. The following example output indicates the count of the icmp_unrch_interval counter before
sending the 100 packets. Notice that the count is zero.

Router#

show pxf cpu statistics drop

FP drop statistics

packets bytes

reasm_err_or_badmtu 0 0

mpls_no_eos 0 0

fib_zero_dest 0 0

fib_drop_null 0 0

fib_icmp_no_adj 0 0

fib_icmp_bcast_dst 0 0

mfib_ttl_0 0 0

mfib_disabled 0 0

mfib_rpf_failed 0 0

mfib_null_oif 0 0

mfib_ttl_threshold 0 0

tfib_rp_flag 0 0

tfib_eos_violation 0 0

tfib_nonip_expose 0 0

tfib_label_invalid 0 0

tfib_path_unknown 0 0

tfib_nonip_ttl_exp 0 0

icmp_unrch_interval 0 0 /*no ICMP packets created*/

icmp_on_icmp 0 0

icmp_bad_hdr 0 0

icmp_multicast 0 0

icmp_frag 0 0

macr_bad_tag_num 0 0

no_touch 0 0

enq_id_0 0 0

no_pkt_handles 0 0

l2_unsupp_drop 0 0

ipm_replay_full 0 0

bad_atm_arp 0 0

nested_fragmentation 0 0

l2less drop packets 0

Summary of Contents for 10008







































































Search results

Summary of Contents for 10008

Reviews:

Cisco 10008, Installation And Configuration Manual, Page: 44 / 70

Search results

Summary of Contents for 10008

Reviews: