Cisco 10008 Installation And Configuration Manual Download Page 50 | Manualshive

Page: 50 / 70

Cisco 10008 Installation And Configuration Manual Download Page 50

50

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

show pxf cpu access-lists

show pxf cpu access-lists

To display parallel express forwarding (PXF) memory information for access control lists (ACLs), use the

show pxf cpu access-lists

command in privileged EXEC mode.

show pxf cpu access-lists

[

security

|

qos

|

pbr

|

compiled

]

Cisco 10000 Series Router

show pxf cpu access-lists

[

security

[[

tcam

acl-name

[

detail

]] |

flex-sum | children

] |

qos

|

pbr

|

compiled

]

Syntax Description

Command Modes

Privileged EXEC

security

(Optional) Displays information about the security ACLs defined in
Cisco IOS and compiled to the PXF. Also displays information about split
ACLs, such as how much memory has been used.

tcam

acl-name

(Optional) Displays information about the specified security ACL stored in
ternary content addressable memory (TCAM).

Note

This option is only available on the PRE3 and PRE4 for the Cisco
10000 series router.

detail

(Optional) Displays decoded information about the packet fields used for
matching in the TCAM.

flex-sum

(Optional) Displays summary information describing the amount of memory
allocated in the parallel express forwarding (PXF) engine for use by the
flexible key construction microcode. This information is useful for design
teams.

Note

This option is only available on the PRE3 and PRE4 for the Cisco
10000 series router.

children

(Optional) Displays information for child policies. If an ACL is a template
child, the output typically does not display the child information. Specifying
the

children

keyword displays data for child policies, too, and shows the

children and the parent policy of each child.

Use caution when using the

children

keyword as there might be thousands

of child policies configured, which could have negative effects on the
command output.

qos

(Optional) Displays information about the QoS ACLs defined in Cisco IOS
and compiled to the PXF.

pbr

(Optional) Displays information about ACLs for policy-based routing (PBR).

compiled

(Optional) Displays information for all compiled Turbo-ACLs.

The PRE2 supports Turbo-ACLs and the

compiled

option. The PRE3 and

PRE4 accept the PRE2

compiled

option, but do not implement Turbo-ACLs.

«
...
48
49
50
51
52
...
»

Summary of Contents for 10008







































































Reviews:

No comments