manualshive.com logo in svg

Cisco 10008, Installation And Configuration Manual, Page: 5 / 70

Share
Download
Cisco 10008 Installation And Configuration Manual Download Page 5

5

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

  Product Overview

PRE4 Connectors

The front panel on the PRE4 contains three ports with RJ-45 connectors. 

•

Console port (CONSOLE)—This asynchronous serial port is used to connect a terminal to the PRE4 
for local administrative access.

•

Auxiliary port (AUX)—This asynchronous serial port is used to connect a modem to the PRE4 for 
remote administrative access.

•

NME Port—This Ethernet port is used to connect the PRE4 to a Fast Ethernet port.

CompactFlash Card Slot

The external CompactFlash slot can store the Cisco IOS image or a system configuration file on a flash 
memory card. The system can also boot from the software stored on the flash memory card.

LED Indicators and Buttons

The LEDs on the PRE4 front panel provide a visual indication showing the status of PRE4 operation. 

Table 2

 describes the PRE4 LEDs and buttons. 

Note

F or additional information about alarm connections, see the 

Cisco 10000 Series Router Performance 

Routing Engine Installation

 guide at the following URL: 

http://cisco.com/en/US/products/hw/routers/ps133/prod_installation_guides_list.html 

1

Ejector Levers

7

ACO (Alarm Cut-off Button)

2

Console and Auxiliary Ports

8

CompactFlash Slot, Disk0

3

Network Management Ethernet (NME) Port 

9

Slot0 (Disk0) LED 

4

NME Activity and Link LEDs

10

Status, Fail LEDs

5

Push-button reset 

11

Building Internal Timing Source (BITS) LED

6

Alarms: Critical, Major, Minor

12

Alphanumeric Display

Table 2

PRE4 LED Status and Button Descriptions

LEDs and Button

Status

Description

ACTIVITY

Green

Packets are being transmitted and received.

Off

No activity.

LINK

Green

Carrier detected, the port is able to pass traffic.

Off

No carrier detected, the port is not able to pass traffic.

Push-button reset

n/a

Resets the PRE4. 

Summary of Contents for 10008







































































Reviews:

No comments