Cisco 10008 Installation And Configuration Manual Download Page 61

Page: 61 / 70

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

show pxf cpu qos

priority

class low-priority

set atm-clp

class class-default

queue-limit 512

Router#

show pxf cpu qos police_test

Output Policymap: police_test

Vcci: A05 Flags: 4 Policymap_index: 6 Policymap_data_index: 12

OUT AT1/0/0.111 (0x71764660) ref_count 1

Output Action Table Contents for vcci 0xA05 - Policymap index: 6

class-name: high-priority class_index: 0 action_flags: 0x00

srp_class_id: 0x01 prec/dscp: 0x00 cos: 0

discard_class: 0x00 exp_value: 0

class-name: low-priority class_index: 1 action_flags: 0x10

srp_class_id: 0x00 prec/dscp: 0x00 cos: 0

discard_class: 0x00 exp_value: 0

class-name: class-default class_index: 2 action_flags: 0x00

srp_class_id: 0x00 prec/dscp: 0x00 cos: 0

discard_class: 0x00 exp_value: 0

Related Commands

Command

Description

show pxf cpu statistics
qos

Displays match statistics for a service policy on an interface.

Summary of Contents for 10008







































































Search results

Summary of Contents for 10008

Reviews:

Cisco 10008, Installation And Configuration Manual, Page: 61 / 70

Search results

Summary of Contents for 10008

Reviews: