manualshive.com logo in svg

Cisco 10008, Installation And Configuration Manual, Page: 1 / 70

Share
Download
Cisco 10008 Installation And Configuration Manual Download Page 1

Corporate Headquarters:

© 2008 Cisco Systems, Inc. All rights reserved.

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco 10008 Router PRE4 Installation and 
Configuration Guide

Product Number: ESR-PRE4

This publication contains instructions for installing and upgrading the Performance Routing Engine 4 
(PRE4) in a Cisco 10008 router. 

Feature Information for the PRE4 

Table 1

 describes the release history for this feature. The table lists only the Cisco IOS software release 

that introduced support for a given feature in a given Cisco IOS software release train. Unless noted 
otherwise, subsequent releases of that Cisco IOS software release train also support that feature.

Finding Support Information for Platforms and Cisco IOS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image 
support. Access Cisco Feature Navigator at 

http://www.cisco.com/go/fn

. You must have an account on 

Cisco.com. If you do not have an account or have forgotten your username or password, click 

Cancel

 at 

the login dialog box and follow the instructions that appear. 

Table 1

Feature Information for the PRE4 

Feature Name

Releases

Feature Information

PRE4 

12.2(33)SB 

The PRE4 is the fifth generation PXF packet processing 
and scheduling engine for the Cisco 10008 router. 

Summary of Contents for 10008







































































Reviews:

No comments