Cirrus Logic CS5346 Manual Download Page 1

Page: 1 / 38

Copyright



Cirrus Logic, Inc. 2012

Preliminary Product Information

This document contains information for a product under development.

Cirrus Logic reserves the right to modify this product without notice.

http://www.cirrus.com

103-dB, 192-kHz, Stereo Audio ADC with 6:1 Input Mux

ADC Features



Multi-bit Delta–Sigma Modulator



103 dB Dynamic Range



-95 dB THD+N



Stereo 6:1 Input Multiplexer



Programmable Gain Amplifier (PGA)

– ± 12 dB Gain, 0.5-dB Step Size
– Zero-crossing, Click-free Transitions



Stereo Microphone Inputs

– +32 dB Gain Stage
– Low-noise Bias Supply



Up to 192 kHz Sampling Rates



Selectable 24-bit, Left-justified or I²S Serial

Audio Interface Formats

System Features



Power-down Mode



+5 V Analog Power Supply, Nominal



+3.3 V Digital Power Supply, Nominal



Direct Interface with 3.3 V to 5 V Logic Levels



Pin Compatible with CS5345 (*See

Section 2

for details.)

General Description

The CS5346 integrates an analog multiplexer, program-

mable gain amplifier, and stereo audio analog-to-digital

converter. The CS5346 performs stereo analog-to-digi-

tal (A/D) conve rsion of 24-bit serial values at sa mple

rates up to 192 kHz.
A 6:1 stereo input multiplexer is included for selecting

between line-level and microphone-level inputs. The

microphone input path includes a +32 dB gain stage

and a low-noise bias voltage supply. The PGA is avail-

able for line or microphone inputs and provides

gain/attenuation of ±12 dB in 0.5 dB steps.
The output of the PGA is followed by an advanced 5th-

order, multi-bit delta-sigma modulator and digital filter-

ing/decimation. Sampled data is transmitted by the

serial audio interface at rates from 8 kHz to 192 kHz in

either Slave or Master Mode.
Integrated level translators allow easy interfacing be-

tween the CS5346 and other devices operating over a

wide range of logic levels.
The CS5346 is available in a 48-pin LQFP package in

Commercial (-40° to +85° C) grade. The CDB5346 Cus-

tomer Demonstration board is also available for device

evaluation and implementation suggestions. Please re-

fer to

“Ordering Information” on page 38

for complete

details.

3.3 V to 5 V

Low-Latency

Anti-Alias Filter

Internal Voltage

Reference

Multibit

Oversampling

ADC

Multibit

Oversampling

ADC

Low-Latency

Anti-Alias Filter

High Pass

Filter

High Pass

Filter

Stereo Input 1

Serial

Audio

Output

3.3 V

5 V

MUX

eri

rface

vel

Tran

slat

Stereo Input 2

Stereo Input 3

Stereo Input 4 /

Mic Input 1 & 2

Stereo Input 5

Stereo Input 6

PGA

+32 dB

vel

nslat

Reset

I²C



/SPI



Control Data

Interrupt

Overflow

Left PGA Output
Right PGA Output

PGAA

AUG ‘12

DS861PP3

CS5346

Summary of Contents for CS5346







































Search results

Summary of Contents for CS5346

Reviews:

Related manuals for CS5346

Brands by name

Popular brands

Cirrus Logic CS5346, Manual

Search results

Summary of Contents for CS5346

Reviews:

Related manuals for CS5346

Brands by name

Popular brands