HL – heart rate limit 1 / 2
Select with UL- or LL-button
Here you can choose, if the current training
should be within the heart rate limit 1 or the
heart rate limit 2.
Note:
the heart rate time manager (see 6.
“special functions“) always starts (independent from this setting) with
heart rate limit 1.
Hr / C – heart rate bargraph/cadence
bargraph
Select with UL- or LL-button
Here you can choose, if the bargraph (in the
middle of the display) should be used for heart
rate or cadence (see chap. 5.3).
Cd oFF/on – heart rate time manager
on/off
Select with UL- or LL-button
The heart rate time manager enables you to
make an interval training (two countdowns and
two heart rate limits; all can be set in setting
mode 1): train in two consecutive time intervals which can be repea-
ted as often as desired with two depending heart rate limits.
See also chap. 6.2 heart rate time manager.
CL – Time
Set with UL- or LL-button
Setting range = 00:00 - 23:59 / 00:00 – 12:59
AM/PM
Set the current time.
M – Month
Set with UL- or LL-button
Setting range = 1 - 12
Set the current month.
d – Day
Set with UL- or LL-button
Setting range = 1 - 31
(depending to the month)
Set the current date of day.
y – Year
Set with UL- or LL-button
Setting range = 2005 - 2100
Set the current year.
CA oFF/on – Clock alarm
Select with UL- or LL-button
If clock alarm is switched on, next display
shows the setting of the alarm time.
CA – Set alarm time
Set with UL- or LL-button
Adjust the alarm time.
r
– adjust total kilometres/
reset total values
Set with UL- or LL-button
Setting range: 0 – 99999 km /0 - 62136 mi
Reset with short simultaneous pressing UL-
and LL-button.
Here you can adjust the total kilometres and also reset all total values
(and also all daily values). To reset press both left buttons short
simultaneous.
r
– adjust total meters (ft) of altitude (up)/
reset total values
Set with UL- or LL-button
Setting range: 0 – 99999 m /
0 - 32808 ft x10
Reset with short simultaneous pressing UL-
and LL-button.
Here you can adjust the total meters (or feet) of altitude (upwards)
and also reset all total values (and also all daily values). To reset
press both left buttons short simultaneous.
Now all settings are done and the
HAC
is ready for
use.
5. fUnCtIons
Important:
For the
HAC
to calculate and indicate all values (and
store them for the pc evaluation), a recording must be star-
ted (see chap. 6.1).
To start the recording press both left buttons (UL- and LL-
button) simultaneous for 4 sec. (the mountain symbol in the
display ‚ ‚ starts blinking as a sign of a running recor-
ding).
To stop the recording press again both left buttons simulta-
neous 4 sec. (mountain symbol stops blinking).
All minimum, maximum and average values (displayed as MIN /
MAX / AV), except average and maximum speed, and all daily values
(DAY,) except daily travelling time and kilometres, are only calculated
when the recording is started (see chap. 6.1).
If the recording is not started at the beginning of the current training,
the values of the sub-functions doesn‘t show the current values, they
show the values of the last recording.
The
HAC
is equipped with 2 modes: ‚bike mode‘ (when
you insert the
HAC
on the handlebar bracket it automatical-
ly switches to the bike-mode) and ‚no-bike mode‘ (e.g. while running
or skiing). By short pressing both right buttons (UR- and LR-button),
the
HAC
switches to the bike mode for 5 minutes, even
when it is not on the handlebar bracket. This way you can recall the
bike values at any time.
Not all functions are available in all modes. If the
HAC
is
used without being on the handlebar bracket (‚no-bike mode‘), some
functions are missing.
If a small
¿
appears on the right side of the display, the indicated
values apply to Bike 1. In order to display the values for Bike 2,
press both right buttons (UR- and LR-button) simultaneous short
(the changeover is only possible if current speed = 0). A small
¡
will appear on the left side of the display. To switch back to Bike 1,
press again both right buttons simultaneous short, and the display
will show
¿
.
The main functions shown on the upper part of the display
of the
HAC
can be chosen with the UR-button, those
shown on the lower part of the display can be chosen with
the LR-button. The sub-functions can be chosen with the
accompanying left button (UL- or LL-button).
