HL 2 – heart rate upper limit 2
Set with UL- or LL-button
Standard value = 120 bpm (beats per minute)
or the personal upper limit calculated with
C
ICLO
Zone
®
Setting range min. = 30 bpm; max. 240 bpm
HL 2 – heart rate lower limit 2
Set with UL- or LL-button
Standard value = 100 bpm (beats per minute)
or the personal upper limit calculated with
C
ICLO
Zone
®
Setting range min. = 30 bpm; max. 240 bpm
Cd 1 – Countdown 1
Set with UL- or LL-button
Standard value = 10 minutes
Setting range = 0 - 99.59 minutes
1.
Countdown 1 / Countdown 2 is a stop-watch which runs
backwards (see chap. 5.2, “countdown function“). After starting, the
HAC
gives a short signal when CD 1 reaches 0. Then CD
2 starts automatically, when it reaches 0 it gives short signals for 20
sec. If only one countdown is necessary, the other must be set to 0.
2.
These settings are necessary when using the heart rate time
manager (see chap.6. “special functions”).
Cd 2 – Countdown 2
Set with UL- or LL-button
Standard value = 10minutes
Setting range = 0 - 99.59 minutes
Cc oFF/on – Cadence on/off
Select with UL- or LL-button
Standard value = oFF
Here the cadence measurement can be swit-
ched on or off (measurement is only possible
with the optional cadence kit).
The following two settings only appear, when cadence is switched
‚on‘.
UL – upper limit for cadence
Set with UL- or LL-button
Standard value = 180 rpm (rounds per minute)
Setting range min. = 30 rpm; max. 240 rpm
In order to better control your training, a ca-
dence limit (lower and upper limit) can be set.
When current cadence value is below or above the limits, an optical
alarm occurs (cadence value starts blinking).
LL – lower limit for cadence
Set with UL- or LL-button
Standard value = 120 rpm (rounds per minute)
Setting range min. = 30 rpm; max. 240 rpm
U1 – unit kilometre/mile
Select with UL- or LL-button
The unit of measure for distance and speed
can be set here (kilometres or miles).
U2 – Time-of-day display: 24- or 12-hour
Select with UL- or LL-button
If 12-hour indication is selected, automatically
also the american date format (month/day) and
weight unit lbs is chosen.
U3 – Unit °Celsius/°Fahrenheit
Select with UL- or LL-button
The unit of measure for the temperature can be
set here (°celsius or ° fahrenheit).
U4 – Unit altimeter meter (m) /
feet (ft x 10)
Select with UL- or LL-button
The unit of measure for the altitude can be set
here (meter or feet).
UPL – Upload Version
Start with short simultaneous pressing of UL-
and LL-button
Indicates the firmware-version of the
HAC
. If there is a newer firmware available
for your
HAC
(see www.ciclosport.
de), you can start the firmware upload at this point with short
simultaneous pressing both left buttons (UL- and LL-button), that
is only possible with the optional pc-interface and the program
HAC
tronic
.
When the upload is finished correctly, normal mode appears in the
display.
Pd – Power down-mode
Switch on with short simultaneous pressing of
UL- and LL-button
Starts the power-saving mode (see chap. 5.3).
To end the power-saving mode, press any
button.
4.2 setting mode 2
Press LR-button 4 sec.
A – Setting and / or re-adjusting current
altitude
Set with UL- or LL-button
Setting range = -200m to 9000m or
2952 ft x10
The current altitude can be adjusted, if e.g. due to variations in the
air-pressure, the current altitude shown in the
HAC
is not
correct.
A change in the current altitude has no effect on other altitude func-
tions (e.g. total meters). Only if the adjusted altitude is higher than the
current max. altitude, the max. altitude will be changed to the new
value.
DST – adjust daily distance
Set with UL- or LL-button
Standard value = 0 km
Setting range min. = 0,00 km /m;
max.= 999,99 km / 621,36 m
(in the display the comma is shown as a colon)
The daily kilometres can be adjusted here, e.g. as a starting point
in case of tours according to a tour guidebook, if the tour was not
entered at „0“ km.
This setting does not affect the function total kilometres. There only
the really ridden kilometres are counted.
JS oFF/on – Ski mode on/off
Select with UL- or LL-button
If the
HAC
is used while skiing, the
ski speed is only calculated and indicated if this
function is set ‚on‘.
