Countdown
To start the countdown (resp. the
heart rate time manager) press
start/stop-button short.
After starting the
HAC
counts back the indicated time to
zero. Then it gives a short signal and starts automatically the count-
down 2. After counting back the countdown 2, the
HAC
gives a long signal (stop the signal with short pressing any button).
By pressing start/stop-button 3 sec. the countdown is set back to
the start value (of countdown 1).
The function ‚countdown‘ is also used by the function ‚heart rate
time manager‘, see chap. 6.2.
Comparison
(only in bike mode)
See also chap. 6.4. The current tour can be
compared with a previous tour (same course).
During the comparison, the display shows
constantly if you are faster or slower as on the
compared tour (accuracy = +/- 1 sec.).
To choose the tour being compared, see below. At the end of the
comparison a short signal tones and the recording is automatically
stopped. The last compare time is still indicated and the ‚new‘ tour is
stored for a new comparison.
To start the comparison (and with this start the recording) press the
UL- and LL-button simultaneously 4 sec. (to stop the comparison
premature press again the UL- and LL-button simultaneously 4 sec).
Choose a tour for comparison
(only in bike mode)
Sub-function of function ‚Comparison‘ (see
also 6.4).
Press the LL-button repeatedly short, all stored
tours are (descending) indicated in the display
(date and start time appear changing). The tour you leave indicated
in the display, is chosen. If you do not want to choose a tour, leave
the “----“ indicated in the display.
After choosing the tour, press UL- and LL-button simultaneously
4 sec. to start the comparison (and therewith start the recording).
Note:
A tour for comparison can only be chosen, when the recor-
ding is not yet started.
Cadence (optional)
(only in bike mode)
The function ‚Cc‘ must be switched ‚on‘ in
setting mode 1 (chap. 4.1) and the optional
cadence cable must be mounted to measure
and indicate the cadence.
Range: 0 - 240 rpm (= revolutions per minute )
Average cadence
(only in bike mode)
Sub-function of function ‚Cadence‘.
Indicates the average cadence of the current
tour.
Range: 0 - 240 rpm
Maximum cadence
(only in bike mode)
Sub-function of function ‚Cadence‘.
Indicates the maximum cadence of the current
tour.
Range: 0 - 240 rpm
Number of revolutions
(only in bike mode)
Sub-function of function ‚Cadence‘.
Indicates the number of revolutions of the
current tour.
Range: 0 – 999999 revolutions (the 6. position
is shown on the decimal point of the upper
display)
Daily ride time
(only in bike mode)
Indicates the time travelled (without stopping-
times, i.e. the time is only calculated when the
wheel turns).
The measurement starts with the first and ends
4 sec. after the last turn of the wheel.
Range: 0 – 999:59 (up to 10 hours the display shows: h:mm:ss, 10
hours and more: hhh:mm)
Sum of the daily ride time
(only in bike mode)
Sub-function of the function ‚Daily ride time‘.
Indicates the sum of the time travelled with bike
1 and bike 2.
Range: 0 – 999:59 (up to 10 hours the display
shows: h:mm:ss, 10 hours and more: hhh:mm)
Total ride time
(only in bike mode)
Sub-function of the function ‚Daily ride time‘.
Indicates the total time travelled.
Range: 0 - 999:59 h
Sum of total ride time
(only in bike mode)
Sub-function of the function ‚Daily ride time‘.
Indicates the sum of the total time travelled with
bike 1 and bike 2.
Range: 0 - 999:59 h
Current altitude
Indicates the current altitude in meters or ft x10
(above sea level). It is indicated in steps of 1
m/10 ft .
As the altitude depends on the air-pressure,
the measurement may vary according to the
weather situation.
Range: -200m to 9000m resp. 2952 ft x10
Daily altitude increasing
Sub-function of function ‚Current altitude‘
Indicates the current increase (meters/ft) in
altitude for the current tour.
Range: 0 - 99999 m resp.
32808 ft x10
Daily altitude decreasing
Sub-function of function ‚Current altitude‘
Indicates the current decrease (meters/ft) in
altitude for the current tour.
Range: 0 - 99999 m resp.
32808 ft x10
Total altitude increasing
Sub-function of function ‚Current altitude‘
Indicates the total increase (meters/ft) in alti-
tude.
Range: 0 - 99999 m resp.
32808 ft x10
Total altitude decreasing
Sub-function of function ‚Current altitude‘
Indicates the total decrease (meters/ft) in
altitude.
Range: 0 - 99999 m resp.
32808 ft x10
Note:
Technically restricted the daily and total amount of meters/ft.
are only added if at least 2 meters have been exceeded.
10
