background image

7  -  STANDARD CONTROL OPERATIONS AND OPTIONS

7.6  Built-in DHW and space heating control 

AQUACIAT

CALEO

 units are specially designed to optimise the 

operation of heating installations that require hot-water production 

for  traditional  heating  (SHC)  and  domestic  hot  water  (DHW) 

requirements.

Connect Touch permits constant and automatic optimisation 

of the unit:

•  Control of a three-way directional on/off valve based on 

the heating or domestic hot water requirements (3-way 

valve used to switch between Space Heating Control and 

Domestic Hot Water). By default, the unit is operating in 

Space Heating mode.

•  Control of the electric heater stages can complement the 

heating loop (1 to 4 electric heating stages). 

See section 

7.7.2

7.6.1  Heating or domestic hot water mode

The three-way valve permits switching the heating capacity to 

a heating circuit (fan coil units, radiators or floor heating), or to 

a domestic hot water tank. If the unit is in domestic hot water 
production mode, a “DHW” message is displayed on the user 

interface next to the current operating mode.

The unit requests changeover to DHW mode provided that 

both water tank conditions and unit conditions are met:

•  Water tank conditions:

•  “DHW Request Input” volt-free contact is closed or 

“DHW Tank Temperature” is below “DHW Setpoint” 

AND

•  The third timer program (schedule 3) is set to occupied 

(DHW mode requested) and the anti-legionella 
program is not requested (see section 

5.9

).

•  Unit conditions:

• 

Summer mode is active (space heating is not required) 

OR

• 

Summer mode is NOT active and the minimum SHC 
operating time and the maximum DHW operating time 
parameters allow for that (service-configured parameters).

NOTE: Domestic Hot Water schedule can be activated 

regardless of the current operating mode (Local/Remote/Net).

Based on the operating mode (SHC or DHW) the water setpoint 

is adjusted:

•  In heating mode, hsp1 and hsp2 are used. They can be 

modified by user reset (see section 7.5.2

).

•  In domestic hot water production mode, DHW setpoint is 

used. No setpoint reset is used.

The unit requests changeover to the heating mode if at least one 
of the following conditions applies:

•  The volt-free tank request contact is open.
• 

The maximum operating time for the DHW mode has 

elapsed.

•  Time schedule 3 is in an unoccupied period  

(DHW mode not requested).

If a mode change is requested while a compressor is operating, 
it is stopped before the three-way valve changes to the new 
mode, and then the unit is re-started.

7.6.2  Anti-legionella

Water storage tanks where the water may stagnate for some 
time could create the environment allowing for the growth of 
legionella bacteria. To prevent the risk of legionella growth in the 
hot water tank, the control performs the anti-legionella treatment 
which means that water temperature is increased until it reaches 
the Anti-Legionella setpoint (legionella bacteria do not survive in 
temperature at 60°C).

The anti-legionella program can be activated automatically via 
the schedule setting. To activate the anti-legionella program, 
the installer should set the fourth timer program (schedule 4). 
The water tank temperature is increased until the anti-legionella 
setpoint [leg_sp] is reached or a 6-hour period has elapsed. 
The program cannot be activated more than once within 
6 hours. For more information about setting the anti-legionella 
schedule, see section 

5.9

.

7.6.3  Summer mode

The Summer mode is used to control Domestic Hot Water mode. 
When the Summer mode is active, space heating is not required, 

and the unit can increase the water temperature in the water tank 
in order to provide hot domestic water.

The Summer mode can be activated only when the outdoor air 
temperature  exceeds  the  predefined  Summer  OAT  threshold 
(“Maximum OAT Threshold”).

To set Summer OAT threshold

1. Navigate to the Configuration menu.
2. Select 

Heat/Cool Configuration 

(HCCONFIG).

3. Set

 Maximum OAT Threshold 

[max_th].

Maximum OAT Threshold [max_th]
5 to 100°C

100°C

The  Summer  mode  will  end  when  the  outdoor  air  temperature 
drops  below  the  predefined  Summer  OAT  threshold  -  2K, 
e.g.  if  the  Summer  OAT  threshold  is  set  to  20°C,  the  Summer 

mode will end as soon as the outdoor air temperature reaches 

the temperature of 18°C. 

NOTE: When the Maximum OAT Threshold parameter is 

set to an unreachable value, e.g. 100°C, then the Summer 

mode will be disabled.

 

 

EN - 23 AQUACIAT

CALEO

Summary of Contents for AQUACIAT CALEO CONNECT TOUCH

































Reviews: