55
3.9
Info
This section gathers together useful information for the identification of the
combiner model and the firmware release. This information may be requested by
technical assistance in order to identify the product more easily and give appropriate
suggestions for its use.
!
Key in the code:
(Default MASTER code)
!
Press the button:
(Programming)
!
Press the button:
(
Info
)
!
This will be displayed:
!
Press the button:
or
!
This will be displayed:
!
Press the button:
or
This will be displayed:
3.10
Reset to default settings
To return the combiner to the default settings, it is necessary to carry out the
following sequence:
!
remove the power
!
keep the setup button pressed (see para 2.1)
!
return power to the combiner
!
release the setup button
!
press the
button 5 times before 10 seconds are up
The default settings are:
M o d e l
2
C h a n n e l
P S T N
_
_
R e l .
F i r m w a r e
6 1 7 a S W - 1 . 0 1
I M E I . . .
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Programmation
54
TDC26-TDC36-TM26GSM-TM66GSM-ERMES2- User’s manual
3.9
Codes
The combiner manages two codes, both of four numbers, one
MASTER
and one
COMMANDS
.
Using the
MASTER code
permits total control of the combiner with access to the
local and remote commands, and with the possibility of programming the combiner.
Using instead the
code COMMANDS
there are the limitation: not possible the
command for Stop all Cycles of allarm,Out of order and remittance in order,access at
the programmation and at the Telephone function.The remote commands of Stop
cycle in course,Stop total cycles,Listen of remote withspeakerphone.
!
Key in the code:
(Default MASTER code)
!
Press the button:
(Programming)
!
Press the button:
(
Codes
)
!
This will be displayed:
!
Press the button:
or
!
This will be displayed:
Key the MASTER code to be stored and press the
or
.
Once the MASTER code has been assigned, use the
or
keys and then
press the
or
to assign the COMMANDS code.
!
This will be displayed:
!
Press the button:
or
!
This will be displayed:
Key the COMMANDS code to be stored and press the
or
.
NOTE:
when the code is not enabled for access to a menu, “NOT
PERMITTED” will appear on the display.
NOTE: the maximum length of both the MASTER code and the COMMANDS
code to be inserted is
4 numbers
.
Should one of the MASTER code, it is possible to directly access the
combiner programming by holding down the SETUP key for 15 seconds
(see para 2.1).
C O D E
S E L E C T I O N
M A S T E R
C O D E
_
_
M A S T E R
C O D E
- - - -
_
C O D E
S E L E C T I O N
C O M M A N D S
C O D E
_
_
C O M M A N D S
C O D E
- - - -
_
Address book
Description foraddress book
Vocal messages
Channel 1
Channel 2
Output 1
Output 2
Remote control
Reply pulse
Number of calls
Number Messagges
MASTER code
COMMAND code
nessun number programmed
“Number 01...16”
All cancel
Activation: Impulse NA; Input INT: In INT 1; Delay: 0000
Text messagges
description equal to the first line of the display
Activation: No active; Input INT: Off; Delay: 0000
Mode: ON/OFF; Input Refer.: In INT1; Duration impulse: 01
Mode: ON/OFF; Input Refer.: No Input; Duration impulse: 01
ON
03
3
3
1234
5678
Language
unchanged
