manualshive.com logo in svg

Chrysler PT Cruiser, Service & Repair Manual, Page: 1769 / 2078

Share
Download
Chrysler PT Cruiser Service & Repair Manual Download Page 1769

SIDE VIEW MIRROR GLASS

REMOVAL

WARNING: ALWAYS WEAR EYE AND HAND PRO-
TECTION WHEN SERVICING THE MIRROR ASSEM-
BLY. FAILURE TO OBSERVE THESE WARNINGS
MAY RESULT IN PERSONAL INJURY FROM BRO-
KEN GLASS.

(1) Carefully pull/pry the broken glass holder from

the mirror assembly.

(2) Disconnect the heated mirror electrical connec-

tors from the terminals on the mirror glass holder, if
equipped.

INSTALLATION

CAUTION: It is important to make sure the motor is
square to the glass holder (attaching fingers) prior
to glass holder attachment, otherwise the glass
holder could be installed incorrectly causing poor
retention and possible repeat failure.

(1) Position the new mirror glass holder to the

mirror assembly.

NOTE: Position the mirror glass holder so that the
moisture drain hole on the mirror glass holder
assembly is facing downward.

(2) Align the mirror glass holder’s attaching fin-

gers to the mirror motor housing.

NOTE: Ensure that the protective rubber cover of
the mirror motor housing is positioned correctly
around the bottom of the fingers area.

(3) Using one hand, firmly press the mirror glass

holder assembly into place while at the same time
supporting the housing assembly from the backside
with the other hand.

NOTE: Pressure must be applied equally over the
center portion of the mirror to engage the mirror
glass holder’s attaching fingers to the correspond-
ing fingers on the housing assembly. One or more
clicks may be heard when finger engagement takes
place.

(4) Verify retention of the mirror glass holder

assembly by gently pulling outward on the mirror
glass holder.

BODY SIDE MOLDINGS

REMOVAL

(1) Using a grease pencil or equivalent, mark the

location of the molding for reference during installa-
tion.

(2) Warm the body side molding and body metal to

approximately 38°C (100°F) using a suitable heat
lamp or heat gun.

(3) Pull the molding from the vehicle.
(4) Clean off all traces of adhesive tape residue

from the panel(s) with a general purpose adhesive
remover.

INSTALLATION

(1) Clean panel surface with isopropyl alcohol and

wipe surface dry with a lint free cloth.

(2) Remove the protective cover from the tape on

the back of the molding and apply to the body accord-
ing to the reference points marked previously.

(3) Firmly press the molding to the body surface to

insure adhesion.

WOOD GRAIN/FLAME DECALS

REMOVAL

(1) Using a grease pencil or equivalent, mark the

location of the decals to aid installation.

(2) Using a heat gun, gently apply heat in a circu-

lar motion to loosen the adhesive bond.

(3) Using your fingernail, plastic or wood trim

stick, lift up and peel away the decal from the body
panel applying heat as you go.

(4) Clean off all traces of adhesive from the pan-

el(s) with a general purpose adhesive remover.

INSTALLATION

Surface Preparation

(1) Clean vehicle surfaces, removing any grease/oil

marks using a 50 percent mixture of a isopropyl alco-
hol and water or 3M

t

High Performance Cloth.

(2) Dry surface using a lint free cloth.

Application

NOTE: Decal and vehicle temperatures should be
between 13-32C (55-90F).

NOTE: Vehicle surface must be free of wax, grease,
oil, etc.

PT

EXTERIOR

23 - 41

Summary of Contents for PT Cruiser































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments