Chrysler PT Cruiser Service & Repair Manual Download Page 1467

Page: 1467 / 2078

REMOVAL

(1) Remove transaxle assembly. (Refer to 21 -

TRANSMISSION/TRANSAXLE/MANUAL

REMOVAL)

(2) Using Tool 8870 attached to Tool C-3752,

remove detent plug(s) from transaxle case (Fig. 131).

INSTALLATION

NOTE: Inspect detent plug for signs of wear or
damage. If necessary, replace detent plugs with
new upon installation.

(1) Install detent plug into case (Fig. 132).
(2) Using soft-tipped hammer, drive detent plug

into case until it bottoms (Fig. 133)

(3) Install transaxle assembly. (Refer to 21 -

TRANSMISSION/TRANSAXLE/MANUAL - INSTAL-
LATION)

Fig. 131 Detent Plug Removal

1 - TOOL C-3752
2 - TOOL 8870
3 - DETENT PLUG

Fig. 132 Detent Plug Installation

1 - DETENT PLUG

Fig. 133 Seat with Soft-Tipped Hammer

1 - DETENT PLUG
2 - SOFT-TIPPED HAMMER

G288 MANUAL TRANSAXLE

21 - 55

DETENT PLUG (Continued)

«
...
1465
1466
1467
1468
1469
...
»

Summary of Contents for PT Cruiser































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for PT Cruiser

Reviews:

Chrysler PT Cruiser, Service & Repair Manual, Page: 1467 / 2078

Search results

Summary of Contents for PT Cruiser

Reviews: