manualshive.com logo in svg

Chrysler PT Cruiser, Service & Repair Manual, Page: 1185 / 2078

Share
Download
Chrysler PT Cruiser Service & Repair Manual Download Page 1185

(15) Connect exhaust system to manifold (Fig. 10)

or (Fig. 11).

(16) Connect the downstream oxygen sensor.
(17) Turbocharger equipped vehicles: Install

charge air cooler hoses (Fig. 9).

(18) Install generator and mounting brackets.
(19) Install accessory drive belts (Refer to 7 -

COOLING/ACCESSORY

DRIVE/DRIVE

BELTS

-

INSTALLATION).

(20) Install axle shafts (Refer to 3 - DIFFEREN-

TIAL & DRIVELINE/HALF SHAFT - INSTALLA-
TION).

(21) Install right inner splash shield.
(22) Install wheels and lower vehicle.
(23) Install cooling module assembly (fan, radiator,

A/C condenser, transmission oil cooler). Connect radi-
ator fan electrical connector.

(24) Turbocharger equipped vehicles: Connect

power steering hoses to radiator.

(25) Manual Transmission equipped vehicles:

(a) Connect clutch hydraulic line (Fig. 7).
(b) Connect transmission shift linkage.
(c) Connect transmission electrical connectors.

NOTE: It is not necessary to bleed the clutch
hydraulic system. The quick-connect fittings close
immediately after disconnection; allowing no fluid
to escape.

(26) Automatic Transmission equipped vehi-

cles:

(a) Connect transmission oil cooler lines using

service splice kit. Refer to instructions provided
with kit.

(b) Connect transmission electrical connectors.
(c) Connect transmission shift linkage.

(27) Connect A/C lines at junction near upper

torque strut.

(28) Connect upper A/C line to A/C condenser.
(29) Install upper and lower radiator hoses.
(30) Install upper radiator closure panel and cen-

ter brace (Refer to 23 - BODY/EXTERIOR/RADIA-
TOR CLOSURE PANEL - INSTALLATION) (Fig. 6).

(31) Install grille (Refer to 23 - BODY/EXTERIOR/

GRILLE - INSTALLATION).

(32) Connect fuel line and heater hoses.
(33) Connect coolant reserve/recovery hose to cool-

ant outlet connector.

(34) Connect brake booster vacuum hose to intake

manifold.

(35) Connect the proportional purge hose to throt-

tle body.

(36) Install all ground straps and connect engine

wiring harness.

(37) Position PDC and install bolts (Fig. 5). Con-

nect positive battery cable to PDC and ground wire
to vehicle body.

Fig. 17 Positioning Engine Cradle Support Post

1 - POST LOCATING HOLES IN BLOCK
2 - POST POSITIONED UNDER BRACKET
3 - POST LOCATING HOLE IN STRUT
4 - SAFETY STRAPS

5 - FLOOR JACK
6 - SPECIAL TOOL 6848
7 - SPECIAL TOOL 6135
8 - SPECIAL TOOL 6710

PT

ENGINE 2.4L DOHC

9 - 165

ENGINE 2.4L DOHC (Continued)

Summary of Contents for PT Cruiser































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments