manualshive.com logo in svg

Christie RS232, Technical Reference, Page: 4 / 25

Share
Download
Christie RS232 Technical Reference Download Page 4

Christie MicroTiles Serial Commands Technical Reference

4

020-101547-01 Rev. 1 (03-2015)

Introduction

This document provides information and procedures for using serial commands (ASCII text 
messages) to control MicroTiles and ECUs in the array.

RS232 Communication Parameters

This table lists the communication parameters for the display cube RS232 port.

Connect to the RS232 Port

You can use an RS232 connection to remotely access display controls and image setups, issue 
commands or queries, and receive replies.

1. Connect one end of a null standard 9-pin female to female modem cable to the projector RS232 

port.

2. Connect the other end of the null standard 9-pin female to female modem cable to a computer.

Terminal Program Setup

To setup terminal program for proper echoing, see below:

TeraTerm

Setup->Terminal->Local echo: checked
Setup->Terminal->New-Line->Transmit: “CR+LF”

Parameter

Value

Baud rate

115200 bps

Stop bits

1 bit

Data bits

8 bits

Parity

None

Flow control

None

TCP/IP port

3002

Summary of Contents for RS232


























Reviews:

No comments