background image

NOTICES 

COPYRIGHT AND TRADEMARKS 

Copyright © 2015 Christie Digital Systems USA Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may 
not be reflected in this document. Christie reserves the right to make changes to specifications at any time without notice. Performance 
specifications are typical, but may vary depending on conditions beyond Christie's control such as maintenance of the product in 
proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no 
warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. 
Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or 
use of this material. Canadian manufacturing facility is ISO 9001 and 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your 
Christie dealer or Christie. In addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the 
extent relevant or applicable to your product, the warranty does not cover:

a. Problems or damage occurring during shipment, in either direction.

b. Projector lamps (See Christie’s separate lamp program policy).

c. Problems or damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp other than a Christie 

lamp supplied by Christie or an authorized distributor of Christie lamps.

d. Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, 

DVD players, etc., or use of a product with any non-Christie interface device.

e. Problems or damage caused by the use of any lamp, replacement part or component purchased or obtained from an 

unauthorized distributor of Christie lamps, replacement parts or components including, without limitation, any distributor offering 
Christie lamps, replacement parts or components through the internet (confirmation of authorized distributors may be obtained 
from Christie).

f. Problems or damage caused by misuse, improper power source, accident, fire, flood, lightning, earthquake or other natural 

disaster.

g. Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service 

personnel or a Christie authorized repair service provider.

h. Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been 

designed, modified or approved by Christie for such use.

i. Problems or damage caused by use of a projector in the presence of an oil-based fog machine or laser-based lighting that is 

unrelated to the projector.

j. For LCD projectors, the warranty period specified in the warranty applies only where the LCD projector is in “normal use” which 

means the LCD projector is not used more than 8 hours a day, 5 days a week.

k. Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such 

product is protected from precipitation or other adverse weather or environmental conditions and the ambient temperature is 
within the recommended ambient temperature set forth in the specifications for such product.

l. Image retention on LCD flat panels.

m.Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated.  The warranty also does not 
apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office 
in the country where the end user is located or (ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Please see the Maintenance 
section for specific maintenance items as they relate to your product. Failure to perform maintenance as required, and in accordance 
with the maintenance schedule specified by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial 
environment. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. Operation of the product in a residential area is likely to 
cause harmful interference in which case the user will be required to correct the interference at the user’s own expense.

Summary of Contents for Mirage 4K25





































Reviews: