Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0 kW Setup Guide
2-3
020-100751-03 Rev. 1 (02-2014)
2.1.2 Position the Projector
2 people are required to safely lift and install the projector.
Place the projector on a sturdy, level surface and position it so that it is perpendicular to the screen at a suitable
distance. The further back the projector is positioned for the screen, the larger the image will be.
To level the projector adjust the 3 feet. With the projector positioned perpendicular to the screen the image will
appear rectangular instead of keystoned.
2.1.3 Connect a Source
The input panel where all source connections are made, is located at the back of the projector. Each input is
clearly labeled for easy identification. Depending on the type of option card installed, connect your source
using the appropriate cable(s), as follows:
•
Analog Input Card
:
Connect 3-, 4-, or 5-wire RGB source to Red/Pr, Green/Y, Blue/Pb, H/C and V using 3,
4 or 5 BNC connectors as required.
•
Dual 3G/HD/SD-SDI Input Card:
Connect the SDI (Serial Digital Interface) cable to one of the two inputs,
1-IN or 2-IN. Both standard-definition (SD) and high-definition (HD) signals are accepted and automatically
recognized on either input.
•
Dual Link DVI Input Card:
Connect a single or dual DVI video signal to the DVI-I connector, an analog
video signal to the DVI-I connector or an analog video signal to the VGA connector. The DVI signal may
contain HDCP (High-Bandwidth Digital Content Protection).
•
Twin HDMI Input Card:
Connect HDMI (High-Definition Multimedia Interface) cable to one of the two
inputs, 1-IN or 2-IN.
•
Video Decoder Input Card:
Depending on the source you can apply the following;
• Composite video source to 1-CVBS, using a BNC Cable
NOTE:
Same signal can be used on 4, 5 or 6 when input is selected as CVBS.
• A component signal on Inputs 4(Pr), 5(Y), 6(Pb) using BNC Connectors.
NOTE:
Grouped as a component input, YPbPr
.
• S-Video to one of the two, 2-SVID or 3-SVID using S-Video cable.
• S-Video using two BNC cables, with Luma (Y) connected to 4 (Sy) and Chroma (C) connected to 6 (Sc).
NOTE:
Must be grouped as 1 S-Video + 1 CVBS.
•
DMX512 Interface Card:
Has two 5pin XLR connectors - 1 (input) male and 1 (output) female. If there is
active communications on the DMX512 Interface card the power LED will blink between low intensity and
high intensity.
•
Twin DisplayPort Input Card:
Accepts DisplayPort 1.1a inputs from one or two DisplayPort sources.
2.1.4 Connect the Line Cord
High leakage current. Earth connection essential before connecting supply.
IMPORTANT!
Use the line cord provided with the projector, or make sure you are using a line cord, power
plug and socket that meet the appropriate rating standards. Voltage and current requirements
are listed on the license label, located at the back of the projector. This product can be
connected to an IT power distribution system.
To prevent the line cord from inadvertent disconnection, perform one of the following steps:
Summary of Contents for J 2.0 kW
