Chiltrix CX34-4 Installation And Operation Manual Download Page 7

Page: 7 / 54

Chiltrix Inc.

www.chiltrix.com

Piping Examples

PLEASE SEND YOUR PROPOSED FINAL DESIGN TO CHILTRIX SUPPORT DEPARTMENT FOR

APPROVAL, COMMENTS, AND SUGGESTIONS

Pipe Insulation

All loop piping must be insulated per local and national mechanical codes. Any piping in a

system with chilled water (used for cooling) must also be sealed vapor tight to prevent

condensate issues. For design tips and a thickness calculator please visit

http://www.armacell.us/knowledge-center/

See Design Guide Here

https://www.chiltrix.com/documents/chiller-options.pdf

PLEASE ALWAYS SUBMIT YOUR DESIGN TO

CHILTRIX FOR APROVAL

Note: The above design should not be used for more than 2x fan coil units.

If more than two, consider using a VCT19 or VCT37 tank and locating the fan

coil units on the load side parallel to the radiant.

Summary of Contents for CX34-4























































Search results

Summary of Contents for CX34-4

Reviews:

Related manuals for CX34-4

Brands by name

Popular brands

Chiltrix CX34-4, Installation And Operation Manual

Search results

Summary of Contents for CX34-4

Reviews:

Related manuals for CX34-4

Brands by name

Popular brands