manualshive.com logo in svg

Chiltrix CX34-4, Installation And Operation Manual

Share
Download
Chiltrix CX34-4 Installation And Operation Manual Download Page 28

Chiltrix Inc.                                                                           

www.chiltrix.com

Onboard External relay Control – Cont’d

Once the relays are wired as shown, the CX34 DIN setting must be changed 

NOTE: RELAY CONTROL SHOULD NEVER BE USED FOR A HEATING OR COOLING “CALL”. IT IS ONLY FOR 

MODE SELECTION.

Heating or cooling calls are not needed or allowed with CX34, as it monitors the 

returning water temperature and always knows what it needs to do.

The switch status can be displayed in the C parameters

C7 is DIN6 AC heating switch mode status; 0=OPEN; 1=CLOSE

C8 is DIN5 AC cooling switch mode status; 0=OPEN; 1=CLOSE

NOTE: Using this relay control option will override inputs from the Chiltrix standard wired 

controller. 

See the Psychrologix manual for important additional information if this applies to you.

Timers as explained elsewhere in this manual will NOT be available when relay control is 

used.

28

IMPORTANT

The C,H, Com terminals are 

DRY CONTACTS. Do NOT apply 

Voltage to the contacts. Only 

connect relays as explained.

Summary of Contents for CX34-4























































Reviews:

No comments

Brands by name

Popular brands

Load more brands