background image

FCA800V/VE

Installation Instructions

2

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.

DEFINITIONS

MOUNTING SYSTEM:

A MOUNTING SYSTEM is the

primary Chief product to which an accessory and/or component

is attached.

ACCESSORY:

AN ACCESSORY is the secondary Chief

product which is attached to a primary Chief product, and may

have a component attached or setting on it.

COMPONENT:

A COMPONENT is an audiovisual item

designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the
corresponding instructions.

 IMPORTANT SAFETY INSTRUCTIONS

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.

WARNING:

RISK OF INJURY TO PERSONS! Do not

place video equipment such as televisions or computer
monitors on FCA800V/VE camera mount surface.

WARNING:

Use of this accessory will decrease the weight

capacity of the mount to which it is attached by the combined
weight of the accessory!

WARNING:

 Use this mounting system only for its intended

use as described in these instructions. Do not use
attachments not recommended by the manufacturer.

WARNING:

Never operate this mounting system if it is

damaged. Return the mounting system to a service center for
examination and repair.

WARNING:

Do not use this product outdoors.

WARNING:

RISK OF INJURY TO PERSONS! Do not use

this mounting system to support video equipment such as
televisions or computer monitors.

IMPORTANT ! :

Make sure the system meets the

following requirements.

Windows® 7, 8, 8.1 or higher

Mac OS® X 10.7 or higher

With:

2.4GHz Intel® Core 2 Duo Processor

2GB RAM or more

USB 2.0 port (USB 3.0 ready)

NOTE:

Refer to milestone.com for the latest software

compatibility requirements.

--SAVE THESE INSTRUCTIONS--

Summary of Contents for Fusion FCA800V





















Reviews: