background image

Page 10

For technical questions, please call 1-800-444-3353.

Item 67854 

        

Part

Description

Qty

1

Shell (Welding Mask)

1

2

Front Cover Lens

1

3

Auto-Darkening Filter

1

4

Inside Cover Lens

1

5

Flat Washer

2

6

Limitation Washer

2

7

Large Limitation Washer

2

Part

Description

Qty

8

Washer

2

9

Tension Adjustment Knob

2

10

Screw

2

11

Ratcheting Headband

1

12

Sweatband

1

13

Shade Control Knob

1

Parts List and Diagram

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM 

IN THIS MANUAL AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER OR DISTRIBUTOR 

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS 

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE 

ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY 

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND 

LICENSED TECHNICIANS, AND NOT BY THE BUYER.  THE BUYER ASSUMES ALL RISK AND LIABILITY 

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS 

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Record Product’s Serial Number Here: 
Note: If product has no serial number, record month and year of purchase instead.

Note:

 Some parts are listed and shown for illustration purposes only, 

and are not available individually as replacement parts.

SAFETY

OPERA

TION

MAINTENANCE

SPECIFICA

TIONS

Summary of Contents for 67854













Reviews: